Sunday 23 June 2013

Ubiquiti Networks EdgeMAX router lite boot sequence after power on (software version 1.1.0)

The following output has been captured off the serial console port of an Ubiquiti Networks EdgeMAX router lite during its boot sequence after power on.

Device is running software version 1.1.0



Serial settings are: 115200 baud, 8 data bits, no parity and 1 stop bit (115200/8-N-1)


Looking for valid bootloader image....
Jumping to start of image at address 0xbfc80000


U-Boot 1.1.1 (UBNT Build ID: 4493936-g009d77b) (Build time: Sep 20 2012 - 15:48:51)

BIST check passed.
UBNT_E100 r1:2, r2:13, serial #: SERIALNUMBER
Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate)
DRAM: 512 MB
Clearing DRAM....... done
Flash: 4 MB
Net: octeth0, octeth1, octeth2

USB: (port 0) scanning bus for devices... 1 USB Devices found
scanning bus for storage devices...
Device 0: Vendor: Prod.: USB Flash Memory Rev: PMAP
Type: Removable Hard Disk
Capacity: 3745.0 MB = 3.6 GB (7669824 x 512) 0
reading vmlinux.64
........................................

8081560 bytes read
argv[2]: coremask=0x3
argv[3]: root=/dev/sda2
argv[4]: rootdelay=15
argv[5]: rw
argv[6]: rootsqimg=squashfs.img
argv[7]: rootsqwdir=w
argv[8]: mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom)
ELF file is 64 bit
Allocating memory for ELF segment: addr: 0xffffffff81100000 (adjusted to: 0x1100000), size 0x7f2a90
Allocated memory for ELF segment: addr: 0xffffffff81100000, size 0x7f2a90
Processing PHDR 0
Loading 79a980 bytes at ffffffff81100000
Clearing 58110 bytes at ffffffff8189a980
## Loading Linux kernel with entry point: 0xffffffff81105cd0 ...
Bootloader: Done loading app on coremask: 0x3
Linux version 2.6.32.13-UBNT (ancheng@ubnt-builder2) (gcc version 4.3.3 (Cavium Networks Version: 2_0_0 build 99) ) #1 SMP Tue Feb 26 11:01:13 PST 2013
CVMSEG size: 2 cache lines (256 bytes)
Cavium Networks SDK-2.0
CPU revision is: 000d0601 (Cavium Octeon+)
Checking for the multiply/shift bug... no.
Checking for the daddiu bug... no.
Determined physical RAM map:
memory: 0000000000034000 @ 000000000186c000 (usable after init)
memory: 0000000006800000 @ 0000000001900000 (usable)
memory: 0000000007c00000 @ 0000000008200000 (usable)
memory: 000000000fc00000 @ 0000000410000000 (usable)
Wasting 350112 bytes for tracking 6252 unused pages
Zone PFN ranges:
DMA32 0x0000186c -> 0x00100000
Normal 0x00100000 -> 0x0041fc00
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x0000186c -> 0x000018a0
0: 0x00001900 -> 0x00008100
0: 0x00008200 -> 0x0000fe00
0: 0x00410000 -> 0x0041fc00
Cavium Hotplug: Available coremask 0x0
PERCPU: Embedded 10 pages/cpu @a8000000020b8000 s10624 r8192 d22144 u65536
pcpu-alloc: s10624 r8192 d22144 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 63895
Kernel command line: bootoctlinux $loadaddr coremask=0x3 root=/dev/sda2 rootdelay=15 rw rootsqimg=squashfs.img rootsqwdir=w mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom) console=ttyS0,115200
PID hash table entries: 1024 (order: 1, 8192 bytes)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Primary instruction cache 32kB, virtually tagged, 4 way, 64 sets, linesize 128 bytes.
Primary data cache 16kB, 64-way, 2 sets, linesize 128 bytes.
Memory: 483444k/491728k available (3478k kernel code, 8064k reserved, 4118k data, 208k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:152
Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=5000000)
Security Framework initialized
Mount-cache hash table entries: 256
Checking for the daddi bug... no.
SMP: Booting CPU01 (CoreId 1)...
CPU revision is: 000d0601 (Cavium Octeon+)
Brought up 2 CPUs
NET: Registered protocol family 16
bio: create slab at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource OCTEON_CVMCOUNT
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 2, 16384 bytes)
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
/proc/octeon_perf: Octeon performace counter interface loaded
octeon_wdt: Initial granularity 5 Sec.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering unionfs 2.5.11 (for 2.6.32.55)
msgmni has been set to 944
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1180000000800 (irq = 58) is a OCTEON
console [ttyS0] enabled
loop: module loaded
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
OcteonUSB: Detected 1 ports
OcteonUSB OcteonUSB.0: Octeon Host Controller
OcteonUSB OcteonUSB.0: new USB bus registered, assigned bus number 1
OcteonUSB OcteonUSB.0: irq 80, io mem 0x00000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
OcteonUSB: Registered HCD for port 0 on irq 80
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
Probing USB hub...
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
L2 lock: TLB refill 256 bytes
L2 lock: General exception 128 bytes
L2 lock: low-level interrupt 128 bytes
L2 lock: interrupt 640 bytes
L2 lock: memcpy 1152 bytes
Bootbus flash: Setting flash for 4MB flash at 0x1f800000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
3 cmdlinepart partitions found on MTD device phys_mapped_flash
Creating 3 MTD partitions on "phys_mapped_flash":
0x000000000000-0x000000080000 : "boot0"
0x000000080000-0x000000100000 : "boot1"
0x000000300000-0x000000310000 : "eeprom"
Waiting 15sec before mounting root device...
hub 1-0:1.0: activate --> -22
usb 1-1: new high speed USB device using OcteonUSB and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
scsi 0:0:0:0: Direct-Access USB Flash Memory PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 7669824 512-byte logical blocks: (3.92 GB/3.65 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (unionfs filesystem) on device 0:12.
Freeing unused kernel memory: 208k freed
Algorithmics/MIPS FPU Emulator v1.5
INIT: version 2.88 booting
INIT: Entering runlevel: 2
Starting routing daemon: rib.
Starting EdgeOS router: migrate rl-system configure.

Welcome to EdgeOS ubnt ttyS0

By logging in, accessing, or using the Ubiquiti product, you
acknowledge that you have read and understood the Ubiquiti
License Agreement (available in the Web UI at, by default,
http://192.168.1.1) and agree to be bound by its terms.

ubnt login:


No comments:

Post a Comment