Thursday 2 October 2014

Aerohive AP230 boot sequence after power on (software version 6.1r6a)





The following output has been captured off the serial console port of an Aerohive AP230 during its boot sequence after power on.

Device is running software version 6.1r6a


Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)


U-Boot 2012.10 (Aug 15 2014 - 00:22:34)

I2C:   ready
DEV ID= 0000cf12
SKU ID = 0
OTP status: eca00018
MEMC 0 DDR speed = 800MHz
Log: ddr40_phy_init.c: Configuring DDR Controller PLLs
Log: offset = 0x18010800
Log: VCO_FREQ is 1600 which is greater than 1Ghz.
Log: DDR Phy PLL polling for lock
Log: DDR Phy PLL locked.
Log: ddr40_phy_init::DDR PHY step size calibration complete.
Log: ddr40_phy_init:: Virtual VttSetup onm CONNECT=0x01CF7FFF, OVERRIDE=0x00077FFF
Log: ddr40_phy_init:: Virtual Vtt Enabled
Log: DDR Controller PLL Configuration Complete
PHY register dump after DDR PHY init
PHY register dump after mode register write
DRAM:  256 MiB
WARNING: Caches not enabled
GPIO Init ... Done
Power Input Detection: DC adaptor, Drive GPIO17(USB 5V enable) success
NAND:   (ONFI),  S34ML04G1, 128 KiB blocks, 2 KiB pages, 16B OOB, 8-bit
NAND:   chipsize 512 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
Unlocking L2 Cache ...Done
arm_clk=1000MHz, axi_clk=500MHz, apb_clk=250MHz, arm_periph_clk=500MHz
Net:   Registering eth
Broadcom BCM IPROC Ethernet driver 0.1
Using GMAC1 (0x18025000)
et0: ethHw_chipAttach: Chip ID: 0xcf12; phyaddr: 0x1e
bcm_robo_attach: devid: 0x53012
bcmiproc_eth-0
MAC address is xxxx:xxxx:xxxx

find_nvram: nvram not found, trying embedded nvram next
find_nvram: no embedded_nvram
find_nvram: no nvram found
Restoring NVRAM Default Configuration
NVRAM header not found
_nvram_init: ret ffffffff
nvram_init: ret ffffffff
Reset TPM chip...
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x580000, size 0x500000
 5242880 bytes read: OK

NAND read: device 0 offset 0xf80000, size 0x2800000
Skipping bad block 0x01b00000
Skipping bad block 0x01b40000
 41943040 bytes read: OK
## Booting kernel from Legacy Image at 01005000 ...
   Image Name:   Linux-2.6.36
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1998304 Bytes = 1.9 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02005000 ...
   Image Name:   uboot initramfs rootfs
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    25042944 Bytes = 23.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
Power off two PHY...
   Loading Kernel Image ... OK
OK
boot_prep_linux commandline: root=/dev/ram console=ttyS0,9600 ramdisk_size=70000 cache-sram-size=0x10000
Using machid 0xbb8 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Mounting local file systems...
[board]: initialize soft i2c by bit-bang.
******** Reset button install intr 117 ok
register snif device on interface eth0.
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.54 (r425351)
register snif device on interface eth1.
eth1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.54 (r425351)
BCM radio init config
Chanspec set to 0xd826
BCM radio init config done
Aerohive Wireless Extension 2.0.0 ... INIT!
Aerohive Forwarding Engine module ... INIT!
Image L7 repository version 3, checking existing L7 repository... ...
Existing L7 repository version 3
Nothing to be done with L7 repository version 3
kddr disable



Welcome to Aerohive Product

AP login:





Wednesday 20 August 2014

Reducing power supply noise on HP N40L Microserver




Two years ago I purchased a HP N40L Microserver to use as offline backup storage to backup documents, photos and other personal files.  The device only gets powered on for short periods while I send or retrieve data from it so I was not originally overly concerned with the fan coil noise I noticed coming from the Microserver's power supply.

Fast forward two years and I had grown tired of the high pitched coil noise even though it was so infrequent.

So I pulled out the power supply, made by Delta Electronics, and removed the fan for inspection.

My Fan has the current specifications:

Manufacturer: T&T
Model:         4020TH12B-PD1
Voltage:       12VDC
Current draw:  0.28A
Size:          40x40x20mm
Pins:          Two
Search Google for this fan

After searching the internet for some time I discovered this may also be sold by Cofan USA with the following specifications:

Manufacturer:            Cofan Usa
Model:                   F-4020TH12B III
Rated Voltage:           12V
Operating Voltage:       8-13.8V
Rated Current (A):       0.28
Actual Current (A):      0.10
Rated Power (W):         3.36
Rated Speed (RPM):       9000
Max Air Flow:            0.31 CMM or 10.90 CFM
Max Static Air pressure: 9.79 mmH2O or 0.39 InH2O
Noise level (dBA):       34.90



Searching the internet and not wanting to spend $20-30 on a fan I managed to find a near match on element14.com for $7 specifications below:

Manufacturer:         Multicomp
Model:                MC36287
Fan Frame Size:       40mm
External Depth:       20mm
Supply Voltage:       12VDC
Current Rating:       115mA

Rated Power (W):      1.38
Rated Speed (RPM):    8200
Flow Rate - Imperial: 10.8 cu.ft/min
Flow Rate - Metric:   0.305 m/min 

Static Air pressure:  0.27 InH2O
Noise Rating:         27.5dBA
Bearing Type:         Vapo



Now with the multicomp fan there are three "issues" that you need to understand or need to resolve.

The first is that the fan comes with bare leads so you need to cut the connector off the old fan and resolder onto your new fan.  Make sure you use some heatshrink tubing or the like and not cheap electrical tape as the fan power wiring comes close to heatsinks and electrical tape is just going to come free after some time.

The second is the screws on the original fan do not fit the Multicomp fan as the mounting holes in the original T&T fan are smaller than those in the Multicomp.  This is not a big deal as the case lid of the Delta Electronics power supply is well designed and pushes up against the fan to eliminate any vibration that would result by the fan not being screwed into the power supply.

The third and last is the fan power cable routing, the Multicomp fan does not have notches cut into both sides of the housing to route the power cables neatly.  To fix this you can use a dremel or other cutting tool to cut a notch, but I found I was able to route the cable in such a fashion that cutting was not required.  This meant the cabling was slightly interfering with the power supply when it was reinserted into the Microserver's chassis, but as there will be no real vibration and I hope to never remove the power supply again I was not concerned.


After reinstalling the power supply and powering on the server I could not believe the difference.  This modification was well worth the hour or so it took completing as well as the $7 and 5 day shipping delay for the fan.

I honestly wished I had performed the swap earlier and even though I may could have initially claimed this issue through HP warranty the shipping and headache declared this not an option for me.




Please drop me a comment if you have found this post useful or if it requires more information.






Thursday 17 April 2014

Realtek RTL8188ETV USB 2.0 wireless LAN adapter




I recently purchased a wireless dongle for my ODROID U3 from eBay and it just arrived.




"lsusb -vv" on my Xubuntu 13.10 displays the following

Bus 001 Device 012: ID 0bda:0179 Realtek Semiconductor Corp.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0bda Realtek Semiconductor Corp.
  idProduct          0x0179
  bcdDevice            0.00
  iManufacturer           1 Realtek
  iProduct                2 802.11n NIC
  iSerial                 3 XXXXXXXXXXXX
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           39
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              500mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           3
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x03  EP 3 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0002
  (Bus Powered)
  Remote Wakeup Enabled


I was actually hoping for a RALINK RL3070 or RL5370, but as you can see the device reports Realtek under iManufacturer

When I google the idProduct 0x0179 I find information leading me to believe this device is a Realtek RTL8188ETV.

When checking one of my favorite sites for wireless chipset information Wikidev I read that the drivers required for this dongle (if your linux build does not currently support it) are the same as RTL8188EU and you can find them on GitHub HERE.







Tuesday 15 April 2014

Avaya VSP4850GTS boot sequence after power on (software version 3.1.0.2)




The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.1.0.2


Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
 Verifying diag image checksum... OK.
 Loading diagnostics image...  DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         9.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106  USB   Register Test             - PASSED
Test 111  DDRAM Walking 1/0s              - PASSED
Test 112  DDRAM Byte/Word/Long            - PASSED
Test 113  DDRAM Power-of-2                - PASSED
Test 121  ROM   Config                    - PASSED
Test 151  FANs  Status                    - PASSED
Test 207  XGS   SWITCH Registers          - PASSED
Test 221  PHYs  Register                  - PASSED
Test 271  Ports Internal Loopback         - PASSED

Starting  Agent  Version:  5.6.2.051


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
 Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.870638] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.065540] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.242491] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
 Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda3: 131/83424 files (9.2% non-contiguous), 44350/333568 blocks
VSP Linux
Thu Jan  1 01:42:08 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...
Writing 4-byte value 797986d0 to e1000000 in /dev/mem
 DISABLING CPLD WatchDog completed OK.

CP1  [01/01/70 01:42:59] rc.appfs.vsp4k: Start
CP1  [01/01/70 01:42:59] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1  [01/01/70 01:42:59] rc.cgroups_class: Cgroup initialization complete.
CP1  [01/01/70 01:42:59] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1  [01/01/70 01:43:01] ins-klm: Detected card type: cp
CP1  [01/01/70 01:43:01] ins-klm: Inserting wdd KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting TIPC
CP1  [01/01/70 01:43:01] ins-klm: Inserting tipc KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1  [01/01/70 01:43:01] ins-klm: inserting KLMs from appfs
CP1  [01/01/70 01:43:01] ins-klm: Inserting evm KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting i2cs KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting oxate KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting oxide KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting carbonate KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting iodate KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting k2 KLM
CP1  [01/01/70 01:43:02] ins-klm: Creating device nodes for K2
CP1  [01/01/70 01:43:02] ins-klm: Creating K2 device files
CP1  [01/01/70 01:43:02] ins-klm: Inserting BDE modules
CP1  [01/01/70 01:43:02] ins-klm: Inserting linux-kernel-bde KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting linux-user-bde KLM
CP1  [01/01/70 01:43:02] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1  [01/01/70 01:43:03] Start:  Starting Applications
CP1  [01/01/70 01:43:03] Start: Detected VSP4K Platform, disable patching
CP1  [01/01/70 01:43:04.000] LifeCycle: INFO: Read restart value of: 1
CP1  [01/01/70 01:43:05.000] LifeCycle: WARNING: Restart count:1
CP1  [01/01/70 01:43:05.000] LifeCycle: INFO: Starting all processes
CP1  [01/01/70 01:43:06.000] Image Sync: Primary Release = 3.1.0.2.GA
CP1  [01/01/70 01:43:06.000] Image Sync: Backup Release  = 3.1.0.0.GA

BANK1: 3.1.0.0.GA
BANK2: 3.1.0.2.GA (CG)
------------------------------------------------------------
 Image Type: UBOOT
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004

 Image Type: KERNEL
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004

 Image Type: ROOT_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004

 Image Type: APP_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004


CP1  [01/01/70 01:43:07.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1  [01/01/70 01:43:13.385] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1  [01/01/70 01:43:15.207] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.


Virtual Services Platform 4800
System Software Release 3.1.0.2
Copyright (c) 2014 Avaya, Inc.

CP1  [01/01/70 01:43:15.208] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1  [01/01/70 01:43:16.118] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1  [01/01/70 01:43:16.118] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.1.0.2
CP1  [01/01/70 01:43:16.801] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1  [01/01/70 01:43:16.842] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1  [01/01/70 01:43:16.884] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1  [01/01/70 01:43:16.886] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1  [01/01/70 01:43:16.892] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1  [01/01/70 01:43:20.421] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1  [01/01/70 01:43:20.439] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1  [01/01/70 01:43:35.688] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1  [01/01/70 01:43:35.688] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1  [01/01/70 01:43:35.695] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg


SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.


SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1  [01/01/70 01:43:36.817] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1  [01/01/70 01:43:36.819] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1  [01/01/70 01:43:36.819] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2014 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.1.0.2
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1  [01/01/70 01:44:25.255] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1  [01/01/70 01:45:36.815] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful



Avaya VSP4850GTS boot sequence after power on (software version 3.1.0.0)




The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.1.0.0


Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
 Verifying diag image checksum... OK.
 Loading diagnostics image...  DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         8.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106  USB   Register Test             - PASSED
Test 111  DDRAM Walking 1/0s              - PASSED
Test 112  DDRAM Byte/Word/Long            - PASSED
Test 113  DDRAM Power-of-2                - PASSED
Test 121  ROM   Config                    - PASSED
Test 151  FANs  Status                    - PASSED
Test 207  XGS   SWITCH Registers          - PASSED
Test 221  PHYs  Register                  - PASSED
Test 271  Ports Internal Loopback         - PASSED

Starting  Agent  Version:  5.6.2.051


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/a/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/a/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
 Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.866695] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.055474] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.232988] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
 Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.7% non-contiguous), 86877/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.7% non-contiguous), 86877/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Block bitmap differences:  -229938
Fix? yes

Free blocks count wrong for group #7 (29171, counted=29172).
Fix? yes

Free blocks count wrong (270821, counted=270822).
Fix? yes


/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
/dev/sda3: 130/83424 files (7.7% non-contiguous), 62746/333568 blocks
VSP Linux
Thu Jan  1 01:25:58 UTC 1970
Uncompressing appfs 'A' ... done
Starting vsp application...
Writing 4-byte value 797984d0 to e1000000 in /dev/mem
 DISABLING CPLD WatchDog completed OK.

CP1  [01/01/70 01:26:50] rc.appfs.vsp4k: Start
CP1  [01/01/70 01:26:51] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1  [01/01/70 01:26:51] rc.cgroups_class: Cgroup initialization complete.
CP1  [01/01/70 01:26:50] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1  [01/01/70 01:26:52] ins-klm: Detected card type: cp
CP1  [01/01/70 01:26:52] ins-klm: Inserting wdd KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting TIPC
CP1  [01/01/70 01:26:52] ins-klm: Inserting tipc KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1  [01/01/70 01:26:52] ins-klm: inserting KLMs from appfs
CP1  [01/01/70 01:26:52] ins-klm: Inserting evm KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting i2cs KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting oxate KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting oxide KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting carbonate KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting iodate KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting k2 KLM
CP1  [01/01/70 01:26:53] ins-klm: Creating device nodes for K2
CP1  [01/01/70 01:26:53] ins-klm: Creating K2 device files
CP1  [01/01/70 01:26:53] ins-klm: Inserting BDE modules
CP1  [01/01/70 01:26:53] ins-klm: Inserting linux-kernel-bde KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting linux-user-bde KLM
CP1  [01/01/70 01:26:53] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1  [01/01/70 01:26:54] Start:  Starting Applications
CP1  [01/01/70 01:26:54] Start: Detected VSP4K Platform, disable patching
CP1  [01/01/70 01:26:55.000] LifeCycle: INFO: Read restart value of: 1
CP1  [01/01/70 01:26:56.000] LifeCycle: WARNING: Restart count:1
CP1  [01/01/70 01:26:56.000] LifeCycle: INFO: Starting all processes
CP1  [01/01/70 01:26:57.000] Image Sync: Primary Release = 3.1.0.0.GA
CP1  [01/01/70 01:26:57.000] Image Sync: Backup Release  = 3.0.1.0.GA

BANK1: 3.1.0.0.GA (CG)
BANK2: 3.0.1.0.GA
------------------------------------------------------------
 Image Type: UBOOT
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: KERNEL
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: ROOT_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: APP_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036


CP1  [01/01/70 01:26:58.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1  [01/01/70 01:27:04.451] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1  [01/01/70 01:27:06.196] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.


Virtual Services Platform 4800
System Software Release 3.1.0.0
Copyright (c) 2013 Avaya, Inc.

CP1  [01/01/70 01:27:06.197] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1  [01/01/70 01:27:07.049] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1  [01/01/70 01:27:07.049] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.1.0.0
CP1  [01/01/70 01:27:07.729] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1  [01/01/70 01:27:07.768] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1  [01/01/70 01:27:07.811] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1  [01/01/70 01:27:07.813] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1  [01/01/70 01:27:07.816] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1  [01/01/70 01:27:11.343] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1  [01/01/70 01:27:11.373] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1  [01/01/70 01:27:26.343] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1  [01/01/70 01:27:26.344] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1  [01/01/70 01:27:26.351] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg


SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.


SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1  [01/01/70 01:27:27.477] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1  [01/01/70 01:27:27.479] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1  [01/01/70 01:27:27.479] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.1.0.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1  [01/01/70 01:28:16.174] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap

CP1  [01/01/70 01:29:27.474] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful



Avaya VSP4850GTS boot sequence after power on (software version 3.0.1.0)




The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.0.1.0


Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
 Verifying diag image checksum... OK.
 Loading diagnostics image...  DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         7.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106  USB   Register Test             - PASSED
Test 111  DDRAM Walking 1/0s              - PASSED
Test 112  DDRAM Byte/Word/Long            - PASSED
Test 113  DDRAM Power-of-2                - PASSED
Test 121  ROM   Config                    - PASSED
Test 151  FANs  Status                    - PASSED
Test 207  XGS   SWITCH Registers          - PASSED
Test 221  PHYs  Register                  - PASSED
Test 271  Ports Internal Loopback         - PASSED

Starting  Agent  Version:  5.6.2.051


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
 Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.857761] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.047291] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.224094] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
 Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.5% non-contiguous), 86075/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.5% non-contiguous), 86075/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda3: 125/83424 files (5.6% non-contiguous), 62306/333568 blocks
VSP Linux
Thu Jan  1 01:06:59 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...

CP1  [01/01/70 01:07:47] rc.appfs.vsp4k: Start
CP1  [01/01/70 01:07:48] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1  [01/01/70 01:07:48] rc.cgroups_class: Cgroup initialization complete.
CP1  [01/01/70 01:07:48] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1  [01/01/70 01:07:50] ins-klm: Detected card type: cp
CP1  [01/01/70 01:07:50] ins-klm: Inserting wdd KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting TIPC
CP1  [01/01/70 01:07:50] ins-klm: Inserting tipc KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1  [01/01/70 01:07:50] ins-klm: inserting KLMs from appfs
CP1  [01/01/70 01:07:50] ins-klm: Inserting evm KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting i2cs KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting oxate KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting oxide KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting carbonate KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting iodate KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting k2 KLM
CP1  [01/01/70 01:07:50] ins-klm: Creating device nodes for K2
CP1  [01/01/70 01:07:50] ins-klm: Creating K2 device files
CP1  [01/01/70 01:07:50] ins-klm: Inserting BDE modules
CP1  [01/01/70 01:07:50] ins-klm: Inserting linux-kernel-bde KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting linux-user-bde KLM
CP1  [01/01/70 01:07:50] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1  [01/01/70 01:07:51] Start:  Starting Applications
CP1  [01/01/70 01:07:52] Start: Detected VSP4K Platform, disable patching
CP1  [01/01/70 01:07:53.000] LifeCycle: INFO: Read restart value of: 0
CP1  [01/01/70 01:07:54.000] LifeCycle: INFO: Initial start
CP1  [01/01/70 01:07:54.000] LifeCycle: INFO: Starting all processes
CP1  [01/01/70 01:07:55.000] Image Sync: Primary Release = 3.0.1.0.GA
CP1  [01/01/70 01:07:55.000] Image Sync: Backup Release  = 3.0.0.0.GA

BANK1: 3.0.0.0.GA
BANK2: 3.0.1.0.GA (CG)
------------------------------------------------------------
 Image Type: UBOOT
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: KERNEL
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: ROOT_FS
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: APP_FS
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036


CP1  [01/01/70 01:07:56.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1  [01/01/70 01:08:02.000] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1  [01/01/70 01:08:03.376] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.


Virtual Services Platform 4800
System Software Release 3.0.1.0
Copyright (c) 2013 Avaya, Inc.

CP1  [01/01/70 01:08:03.377] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1  [01/01/70 01:08:04.297] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1  [01/01/70 01:08:04.297] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.1.0
CP1  [01/01/70 01:08:04.987] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1  [01/01/70 01:08:05.029] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1  [01/01/70 01:08:05.071] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1  [01/01/70 01:08:05.073] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1  [01/01/70 01:08:05.077] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1  [01/01/70 01:08:09.397] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1  [01/01/70 01:08:09.522] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1  [01/01/70 01:08:25.685] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1  [01/01/70 01:08:25.686] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1  [01/01/70 01:08:25.692] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg


SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.


SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1  [01/01/70 01:08:27.405] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1  [01/01/70 01:08:27.477] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1  [01/01/70 01:08:27.494] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.1.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1  [01/01/70 01:09:14.038] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1  [01/01/70 01:10:27.403] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful



How to upgrade a new "out of box" Avaya VSP4850GTS




This guide is to assist those that need an easy and quick guide to upgrade a brand new VSP4850GTS that has just been unboxed.

It is assumed that you know how to unbox the switch, insert power supply, apply power and console into the switch.

We are going to use VLAN1 (10.0.0.1) so we do not have to add a VLAN, use port 1 for the link to a workstation (10.0.0.2).  The workstation used in this guide is a Windows 8 laptop and we are running WinSCP as the FTP client.

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

The encryption module will NOT be downloaded in this example.

Step 1:

  • Login to the switch and perform basic configuration to get the management up.
  • The default username is "rwa" and the default password is "rwa"


Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.0.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: rwa
Password: ***

VSP-4850GTS:1>CP1  [01/01/70 00:36:59.029] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port

VSP-4850GTS:1>en
VSP-4850GTS:1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
VSP-4850GTS:1(config)#interface gigabitEthernet 1/1
VSP-4850GTS:1(config-if)#no shut
VSP-4850GTS:1(config-if)#exit
VSP-4850GTS:1(config-if)#ip address 10.0.0.2 255.255.255.0
VSP-4850GTS:1(config-if)#ping 10.0.0.1
10.0.0.1 is alive
VSP-4850GTS:1(config-if)#


Step 2: 

  • enable the FTP server on the VSP4850GTS

VSP-4850GTS:1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
VSP-4850GTS:1(config)#boot config flags ftpd


Step 3: 

  • using WinSCP copy the .tgz file to the /intflash directory on the VSP4850GTS.  In our example we are upgrading from 3.0.0.0 to 3.0.1.0 so the filename is "VSP4K.3.0.1.0.tgz"

Step 4: 

  • Add and activate the new sofware downloaded

    VSP-4850GTS:1#software add VSP4K.3.0.1.0.tgz
    Extracting distribution information from /intflash/VSP4K.3.0.1.0.tgz
    Extracting software version 3.0.1.0.GA from /intflash/VSP4K.3.0.1.0.tgz
    Extraction of 3.0.1.0.GA to /intflash/release/3.0.1.0.GA successful
    Setting permissions on /intflash/release/3.0.1.0.GA successful
    VSP-4850GTS:1#
    VSP-4850GTS:1#software activate 3.0.1.0.GA
    Executing software activate for version 3.0.1.0.GA.
    Validating release 3.0.1.0.GA
    Sending upgrade message to slots: 1. Version=3.0.1.0.GA

    Slot 1 : IMAGE SYNC: Running pre-install script for image version 3.0.1.0.GA
    Slot 1 : IMAGE SYNC: Uboot image is consistent
    Slot 1 : IMAGE SYNC: Root FS image is being updated...
    Slot 1 : IMAGE SYNC: App FS image is being updated...
    Slot 1 : IMAGE SYNC: Running post-install script for image version 3.0.1.0.GA
    Slot 1 : IMAGE SYNC: Backup image successfully upgraded to 3.0.1.0.GA

    Primary Version:   3.0.1.0.GA
    Backup Version:    3.0.0.0.GA

    Changes will take effect on next reboot.
    VSP-4850GTS:1#

    Step 5: 

    • reboot without save if you wish to have a device with no config changes.  If you would like to keep the FTP and IP address configured perform a "save config".

      VSP-4850GTS:1#save config
      CP-1: Save config to file /intflash/config.cfg successful.

      VSP-4850GTS:1#CP1  [01/01/70 01:00:45.973] 0x000045e3 00000000 GlobalRouter SNMP INFO Save config successful.

      VSP-4850GTS:1#reset
      Are you sure you want to reset the switch (y/n) ? y
      Setting release 3.0.1.0.GA
      CP1  [01/01/70 01:00:53.881] 0x0027458a 00000000 GlobalRouter SW INFO Chassis reset initiated from CLI
      CP1  [01/01/70 01:00:53.881] 0x0027458d 00000000 GlobalRouter SW INFO Resetting Chassis
      CP1  [01/01/70 01:00:56.000] LifeCycle: INFO: Stopping all processes
      CP1  [01/01/70 01:00:57.000] LifeCycle: INFO: All processes have stopped
      CP1  [01/01/70 01:00:57.000] LifeCycle: INFO: Flushing buffers ... OK
      CP1  [01/01/70 01:00:58.000] LifeCycle: WARNING: Restarting module
      INIT: Sending processes the TERM signal
      Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 1977)
      .
      Stopping vsp...
      Deconfiguring network interfaces... done.
      Stopping syslogd/klogd: stopped syslogd (pid 1982)
      stopped klogd (pid 1984)
      done
      Sending all processes the TERM signal...
      Sending all processes the KILL signal...
      hwclock: can't open '/dev/misc/rtc': No such file or directory
      Unmounting remote filesystems...
      Stopping portmap daemon: portmap.
      Deactivating swap...
      Unmounting local filesystems...
      Rebooting... [ 3388.326120] Restarting system.

      U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

      Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

      CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
      Board: Avaya VSP 4850 Switch
      I2C:   ready
      DRAM:  Detected UDIMM UG12T6400M8SU-C8S

         DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
      Now running in RAM - U-Boot at: 3ff79000
      Flash: 64.5 MiB
      PCI:   Bus Dev VenId DevId Class Int
        00:0f.0     - 14e4:b634 - Network controller
      In:    serial
      Out:   serial
      Err:   serial
      Net:   No ethernet found.
      USB:   Register 1210012 NbrPorts 2
      USB EHCI 1.00
      scanning bus for devices... 2 USB Device(s) found
             scanning bus for storage devices... 1 Storage Device(s) found
      Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
      1700040 bytes read
      Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
      10549422 bytes read
       Found DTB file
      WARNING: adjusting available memory to 30000000
      ## Booting kernel from Legacy Image at 01000000 ...
         Image Name:   Linux-2.6.32.21-avaya-vsp4800
         Image Type:   PowerPC Linux Kernel Image (gzip compressed)
         Data Size:    1687686 Bytes = 1.6 MiB
         Load Address: 00000000
         Entry Point:  00000000
         Verifying Checksum ... OK
      ## Loading init Ramdisk from Legacy Image at 01800000 ...
         Image Name:   vsp-image-vsp4800-20130218193035
         Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
         Data Size:    10549358 Bytes = 10.1 MiB
         Load Address: 00000000
         Entry Point:  00000000
         Verifying Checksum ... OK
      ## Flattened Device Tree blob at 0119c0c8
         Booting using the fdt blob at 0x0119c0c8
         Uncompressing Kernel Image ... OK
         Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
         Loading Device Tree to 007fa000, end 007fffff ... OK
      setup_arch: bootmem
      vsp4800_setup_arch()
      arch: exit

      INIT: version 2.86 booting
      Please wait: booting...
      Starting udev
      Root filesystem already rw, not remounting
      Caching udev devnodes
      Populating dev cache
      Creating /etc/default/bios... [    7.873348] sd 0:0:0:0: [sda] Assuming drive cache: write through
      [    8.069709] sd 0:0:0:0: [sda] Assuming drive cache: write through
      [    8.249227] sd 0:0:0:0: [sda] Assuming drive cache: write through
      Configuring update-modules.
      Configuring openssh-sshd.
       Adding system startup for /etc/init.d/sshd.
      Configuring base-files.
      Configuration for powerpc.generic not found, trying powerpc
      Configuring network interfaces... 4800: done.
      Starting portmap daemon: portmap.
      net.ipv4.conf.default.rp_filter = 1
      INIT: Entering runlevel: 5
      Starting OpenBSD Secure Shell server: sshd
      done.
      Starting syslogd/klogd: done
      Starting vsp...
      e2fsck 1.41.14 (22-Dec-2010)
      e2fsck 1.41.14 (22-Dec-2010)
      VSP Linux
      Thu Jan  1 01:06:59 UTC 1970
      Uncompressing appfs 'B' ... done
      Starting vsp application...

      CP1  [01/01/70 01:07:47] rc.appfs.vsp4k: Start
      CP1  [01/01/70 01:07:47] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
      CP1  [01/01/70 01:07:47] rc.cgroups_class: Cgroup initialization complete.
      CP1  [01/01/70 01:07:47] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
      CP1  [01/01/70 01:07:49] ins-klm: Detected card type: cp
      CP1  [01/01/70 01:07:49] ins-klm: Inserting wdd KLM
      CP1  [01/01/70 01:07:49] ins-klm: Inserting TIPC
      CP1  [01/01/70 01:07:49] ins-klm: Inserting tipc KLM
      CP1  [01/01/70 01:07:49] ins-klm: Inserting TUN
      modprobe: module tun not found in modules.dep
      CP1  [01/01/70 01:07:49] ins-klm: inserting KLMs from appfs
      CP1  [01/01/70 01:07:49] ins-klm: Inserting evm KLM
      CP1  [01/01/70 01:07:49] ins-klm: Inserting i2cs KLM
      CP1  [01/01/70 01:07:49] ins-klm: Inserting oxate KLM
      CP1  [01/01/70 01:07:49] ins-klm: Inserting oxide KLM
      CP1  [01/01/70 01:07:50] ins-klm: Inserting carbonate KLM
      CP1  [01/01/70 01:07:50] ins-klm: Inserting iodate KLM
      CP1  [01/01/70 01:07:50] ins-klm: Inserting k2 KLM
      CP1  [01/01/70 01:07:50] ins-klm: Creating device nodes for K2
      CP1  [01/01/70 01:07:50] ins-klm: Creating K2 device files
      CP1  [01/01/70 01:07:50] ins-klm: Inserting BDE modules
      CP1  [01/01/70 01:07:50] ins-klm: Inserting linux-kernel-bde KLM
      CP1  [01/01/70 01:07:50] ins-klm: Inserting linux-user-bde KLM
      CP1  [01/01/70 01:07:50] ins-klm: Creating device nodes for bde KLM {dev-id:126}
      CP1  [01/01/70 01:07:51] Start:  Starting Applications
      CP1  [01/01/70 01:07:51] Start: Detected VSP4K Platform, disable patching
      CP1  [01/01/70 01:07:53.000] LifeCycle: INFO: Initial start
      CP1  [01/01/70 01:07:53.000] LifeCycle: INFO: Starting all processes
      CP1  [01/01/70 01:07:54.000] Image Sync: Primary Release = 3.0.1.0.GA
      CP1  [01/01/70 01:07:54.000] Image Sync: Backup Release  = 3.0.0.0.GA

      BANK1: 3.0.0.0.GA (G )
      BANK2: 3.0.1.0.GA (C )
      ------------------------------------------------------------
       Image Type: UBOOT
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = VSP4K.3.0.1.0int036

       Image Type: KERNEL
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = VSP4K.3.0.1.0int036

       Image Type: ROOT_FS
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = VSP4K.3.0.1.0int036

       Image Type: APP_FS
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = VSP4K.3.0.1.0int036


      CP1  [01/01/70 01:07:55.000] LifeCycle: INFO: All processes started
      Attaching network interface lo0... done.
      CP1  [01/01/70 01:08:01.236] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
      CP1  [01/01/70 01:08:02.831] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.


      Virtual Services Platform 4800
      System Software Release 3.0.1.0
      Copyright (c) 2013 Avaya, Inc.

      CP1  [01/01/70 01:08:02.832] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
      CP1  [01/01/70 01:08:03.533] 0x00034594 00000000 GlobalRouter SW INFO System boot
      CP1  [01/01/70 01:08:03.533] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.1.0
      CP1  [01/01/70 01:08:04.209] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
      CP1  [01/01/70 01:08:04.250] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
      CP1  [01/01/70 01:08:04.294] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
      CP1  [01/01/70 01:08:04.296] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
      CP1  [01/01/70 01:08:04.300] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
      CP1  [01/01/70 01:08:08.439] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
      CP1  [01/01/70 01:08:08.624] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
      CP1  [01/01/70 01:08:21.948] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
      CP1  [01/01/70 01:08:21.948] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
      CP1  [01/01/70 01:08:21.955] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg


      SNMP-v3 VACM configuration is currently using default parameters.
      These parameters should be changed for maximum security.

      SNMP-v3 USM configuration is currently using default parameters.
      These parameters should be changed for maximum security.


      SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

      CP1  [01/01/70 01:08:23.308] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
      CP1  [01/01/70 01:08:23.310] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
      CP1  [01/01/70 01:08:23.310] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

      Copyright(c) 2010-2013 Avaya, Inc.
      All Rights Reserved.
      Virtual Services Platform 4800
      Software Release Build 3.0.1.0
      General Availability Released Software, Fully supported

      AVAYA COMMAND LINE INTERFACE

      Login: CP1  [01/01/70 01:08:25.839] 0x0000c5ec 00300001.239 DYNAMIC CLEAR GlobalRouter HW INFO Link Up(1/1)

      Step 6:

      • commit software so that the upgrade is permanent.  The VSP4850GTS out of the box has auto commit so if left running for 10 minutes the switch will commit the software itself, but if you power down the switch the software activate will not persist and upon powering the switch back up the old software will load.
      Login: rwa
      Password: ***

      You are currently running a new version of code.

      This release will be auto-committed in 9 minutes and 49 seconds.

      Version Running: 3.0.1.0.GA


      VSP-4850GTS:1>CP1  [01/01/70 01:08:34.375] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port
      VSP-4850GTS:1>en
      VSP-4850GTS:1#software commit
      Executing software commit for version 3.0.1.0.GA.

      VSP-4850GTS:1#show software

      ================================================================================
                          software releases in /intflash/release/
      ================================================================================
      3.0.0.0.GA (Backup Release)
      3.0.1.0.GA (Primary Release)

      --------------------------------------------------------------------------------
      Auto Commit     : enabled
      Commit Timeout  : 10 minutes

      VSP-4850GTS:1#


      And that's it, not the most complex procedure, but not the easiest.


      Please leave a comment if you have any questions or if you have found this guide to be useful.  I will attempt to get back to you in a timely manner.


      Avaya VSP4850GTS boot sequence after power on (software version 3.0.0.0)




      The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

      Device is running software version 3.0.0.0


      Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)


      U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

      Reset Status:

      CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
      Board: Avaya VSP 4850 Switch
      I2C:   ready
      DRAM:  Detected UDIMM UG12T6400M8SU-C8S

         DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
      Now running in RAM - U-Boot at: 3ff79000
      Flash: 64.5 MiB
      PCI:   Bus Dev VenId DevId Class Int
        00:0f.0     - 14e4:b634 - Network controller
      In:    serial
      Out:   serial
      Err:   serial
      Net:   No ethernet found.
       Verifying diag image checksum... OK.
       Loading diagnostics image...  DONE.

      Ethernet Routing Switch 4850GTS
      Reading MAC Address...
      MAC Address: XX-XX-XX-XX-XX-XX
      Resets:         5.

      Dip Switch in Non-Base Unit position
      RAM   size:    1GB
      FLASH size:   64MB
      Super ISO is present

      Attaching SOC unit 0... PCI device ASIC attached as unit 0

      Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

      Press Control-C to Enter Diag

      Test 106  USB   Register Test             - PASSED
      Test 111  DDRAM Walking 1/0s              - PASSED
      Test 112  DDRAM Byte/Word/Long            - PASSED
      Test 113  DDRAM Power-of-2                - PASSED
      Test 121  ROM   Config                    - PASSED
      Test 151  FANs  Status                    - PASSED
      Test 207  XGS   SWITCH Registers          - PASSED
      Test 221  PHYs  Register                  - PASSED
      Test 271  Ports Internal Loopback         - PASSED

      Starting  Agent  Version:  5.6.2.051


      U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

      Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

      CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
      Board: Avaya VSP 4850 Switch
      I2C:   ready
      DRAM:  Detected UDIMM UG12T6400M8SU-C8S

         DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
      Now running in RAM - U-Boot at: 3ff79000
      Flash: 64.5 MiB
      PCI:   Bus Dev VenId DevId Class Int
        00:0f.0     - 14e4:b634 - Network controller
      In:    serial
      Out:   serial
      Err:   serial
      Net:   No ethernet found.
      USB:   Register 1210012 NbrPorts 2
      USB EHCI 1.00
      scanning bus for devices... 2 USB Device(s) found
             scanning bus for storage devices... 1 Storage Device(s) found
      Loading file "/boot/a/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
      1700040 bytes read
      Loading file "/boot/a/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
      10549422 bytes read
       Found DTB file
      WARNING: adjusting available memory to 30000000
      ## Booting kernel from Legacy Image at 01000000 ...
         Image Name:   Linux-2.6.32.21-avaya-vsp4800
         Image Type:   PowerPC Linux Kernel Image (gzip compressed)
         Data Size:    1687686 Bytes = 1.6 MiB
         Load Address: 00000000
         Entry Point:  00000000
         Verifying Checksum ... OK
      ## Loading init Ramdisk from Legacy Image at 01800000 ...
         Image Name:   vsp-image-vsp4800-20130218193035
         Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
         Data Size:    10549358 Bytes = 10.1 MiB
         Load Address: 00000000
         Entry Point:  00000000
         Verifying Checksum ... OK
      ## Flattened Device Tree blob at 0119c0c8
         Booting using the fdt blob at 0x0119c0c8
         Uncompressing Kernel Image ... OK
         Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
         Loading Device Tree to 007fa000, end 007fffff ... OK
      setup_arch: bootmem
      vsp4800_setup_arch()
      arch: exit

      INIT: version 2.86 booting
      Please wait: booting...
      Starting udev
      Root filesystem already rw, not remounting
      Caching udev devnodes
      Populating dev cache
      Creating /etc/default/bios... [    7.870429] sd 0:0:0:0: [sda] Assuming drive cache: write through
      [    8.057096] sd 0:0:0:0: [sda] Assuming drive cache: write through
      [    8.235719] sd 0:0:0:0: [sda] Assuming drive cache: write through
      Configuring update-modules.
      Configuring openssh-sshd.
       Adding system startup for /etc/init.d/sshd.
      Configuring base-files.
      Configuration for powerpc.generic not found, trying powerpc
      Configuring network interfaces... 4800: done.
      Starting portmap daemon: portmap.
      net.ipv4.conf.default.rp_filter = 1
      INIT: Entering runlevel: 5
      Starting OpenBSD Secure Shell server: sshd
      done.
      Starting syslogd/klogd: done
      Starting vsp...
      e2fsck 1.41.14 (22-Dec-2010)
      *****************************
      *****************************
      *****************************
      [1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
      fsck from util-linux-ng 2.18
      Pass 1: Checking inodes, blocks, and sizes
      Pass 2: Checking directory structure
      Pass 3: Checking directory connectivity
      Pass 4: Checking reference counts
      Pass 5: Checking group summary information
      /dev/sda2: 1023/128000 files (0.3% non-contiguous), 86012/128000 blocks
      e2fsck 1.41.14 (22-Dec-2010)
      /dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
      *****************************
      *****************************
      *****************************
      [1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
      fsck from util-linux-ng 2.18
      Pass 1: Checking inodes, blocks, and sizes
      Pass 2: Checking directory structure
      Pass 3: Checking directory connectivity
      Pass 4: Checking reference counts
      Pass 5: Checking group summary information
      /dev/sda2: 1023/128000 files (0.3% non-contiguous), 86012/128000 blocks
      [1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
      fsck from util-linux-ng 2.18
      Pass 1: Checking inodes, blocks, and sizes
      Pass 2: Checking directory structure
      Entry 'qos_profile' in /intflash (53089) has deleted/unused inode 53119.  Clear? yes

      Pass 3: Checking directory connectivity
      Pass 4: Checking reference counts
      Pass 5: Checking group summary information

      /dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
      /dev/sda3: 79/83424 files (2.5% non-contiguous), 24822/333568 blocks
      VSP Linux
      Thu Jan  1 00:05:07 UTC 1970
      Uncompressing appfs 'A' ... done
      Starting vsp application...

      CP1  [01/01/70 00:05:53] rc.appfs.vsp4k: Start
      CP1  [01/01/70 00:05:53] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
      CP1  [01/01/70 00:05:53] rc.cgroups_class: Cgroup initialization complete.
      CP1  [01/01/70 00:05:53] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
      CP1  [01/01/70 00:05:55] ins-klm: Detected card type: cp
      CP1  [01/01/70 00:05:55] ins-klm: Inserting wdd KLM
      CP1  [01/01/70 00:05:55] ins-klm: Inserting TIPC
      CP1  [01/01/70 00:05:55] ins-klm: Inserting tipc KLM
      CP1  [01/01/70 00:05:55] ins-klm: Inserting TUN
      modprobe: module tun not found in modules.dep
      CP1  [01/01/70 00:05:55] ins-klm: inserting KLMs from appfs
      CP1  [01/01/70 00:05:55] ins-klm: Inserting evm KLM
      CP1  [01/01/70 00:05:55] ins-klm: Inserting i2cs KLM
      CP1  [01/01/70 00:05:55] ins-klm: Inserting oxate KLM
      CP1  [01/01/70 00:05:55] ins-klm: Inserting oxide KLM
      CP1  [01/01/70 00:05:55] ins-klm: Inserting carbonate KLM
      CP1  [01/01/70 00:05:56] ins-klm: Inserting iodate KLM
      CP1  [01/01/70 00:05:56] ins-klm: Inserting k2 KLM
      CP1  [01/01/70 00:05:56] ins-klm: Creating device nodes for K2
      CP1  [01/01/70 00:05:56] ins-klm: Creating K2 device files
      CP1  [01/01/70 00:05:56] ins-klm: Inserting BDE modules
      CP1  [01/01/70 00:05:56] ins-klm: Inserting linux-kernel-bde KLM
      CP1  [01/01/70 00:05:56] ins-klm: Inserting linux-user-bde KLM
      CP1  [01/01/70 00:05:56] ins-klm: Creating device nodes for bde KLM {dev-id:126}
      CP1  [01/01/70 00:05:57] Start:  Starting Applications
      CP1  [01/01/70 00:05:57] Start: Detected VSP4K Platform, disable patching
      CP1  [01/01/70 00:05:58.000] LifeCycle: INFO: Read restart value of: 2
      CP1  [01/01/70 00:05:59.000] LifeCycle: WARNING: Restart count:2
      CP1  [01/01/70 00:05:59.000] LifeCycle: INFO: Starting all processes
      CP1  [01/01/70 00:06:01.000] Image Sync: Primary Release = 3.0.0.0.GA
      CP1  [01/01/70 00:06:01.000] Image Sync: Backup Release  = 3.0.0.0.GA

      BANK1: 3.0.0.0.GA (CG)
      BANK2: Not Set
      ------------------------------------------------------------
       Image Type: UBOOT
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = UNKNOWN

       Image Type: KERNEL
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = UNKNOWN

       Image Type: ROOT_FS
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = UNKNOWN

       Image Type: APP_FS
        Bank 1: Release Version = VSP4K.3.0.0.0int064
        Bank 2: Release Version = UNKNOWN


      CP1  [01/01/70 00:06:01.000] LifeCycle: INFO: All processes started
      Attaching network interface lo0... done.
      WARNING:  Check dummy: modes fastethernet_interface_configurationspanning-tree
      WARNING:  Check dummy: modes gigabitethernet_interface_configurationspanning-tree


      Virtual Services Platform 4800
      System Software Release 3.0.0.0
      Copyright (c) 2013 Avaya, Inc.

      CP1  [01/01/70 00:06:07.436] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
      CP1  [01/01/70 00:06:07.847] 0x00034594 00000000 GlobalRouter SW INFO System boot
      CP1  [01/01/70 00:06:07.848] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.0.0
      CP1  [01/01/70 00:06:08.548] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
      CP1  [01/01/70 00:06:08.584] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
      CP1  [01/01/70 00:06:08.626] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
      CP1  [01/01/70 00:06:08.628] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
      CP1  [01/01/70 00:06:08.632] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
      CP1  [01/01/70 00:06:09.483] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.
      CP1  [01/01/70 00:06:09.486] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
      Warning: Please save your configuration after boot-up to avoid SNMP access issues.
               RWA, L1, L2, L3 are all mapped to read/write community.
      CP1  [01/01/70 00:06:13.176] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
      CP1  [01/01/70 00:06:13.251] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key

      SNMP-v3 VACM configuration is currently using default parameters.
      These parameters should be changed for maximum security.

      SNMP-v3 USM configuration is currently using default parameters.
      These parameters should be changed for maximum security.


      SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

      CP1  [01/01/70 00:06:29.540] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
      CP1  [01/01/70 00:06:29.541] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
      CP1  [01/01/70 00:06:29.556] 0x0008851c 00000000 GlobalRouter SW INFO Using factory default system configuration
      CP1  [01/01/70 00:06:29.558] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
      CP1  [01/01/70 00:06:29.559] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
      CP1  [01/01/70 00:06:29.560] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

      Copyright(c) 2010-2013 Avaya, Inc.
      All Rights Reserved.
      Virtual Services Platform 4800
      Software Release Build 3.0.0.0
      General Availability Released Software, Fully supported

      AVAYA COMMAND LINE INTERFACE

      CP1  [01/01/70 00:06:30.561] 0x0003c736 00000000 GlobalRouter IP INFO the OSPF Md5 key file does not exist
      Login: CP1  [01/01/70 00:07:17.804] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
      CP1  [01/01/70 00:08:29.557] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful