This guide is to assist those that need an easy and quick guide to upgrade a brand new VSP4850GTS that has just been unboxed.
It is assumed that you know how to unbox the switch, insert power supply, apply power and console into the switch.
We are going to use VLAN1 (10.0.0.1) so we do not have to add a VLAN, use port 1 for the link to a workstation (10.0.0.2). The workstation used in this guide is a Windows 8 laptop and we are running WinSCP as the FTP client.
Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)
The encryption module will NOT be downloaded in this example.
Step 1:
- Login to the switch and perform basic configuration to get the management up.
- The default username is "rwa" and the default password is "rwa"
Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.0.0
General Availability Released Software, Fully supported
AVAYA COMMAND LINE INTERFACE
Login: rwa
Password: ***
VSP-4850GTS:1>CP1 [01/01/70 00:36:59.029] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port
VSP-4850GTS:1>en
VSP-4850GTS:1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
VSP-4850GTS:1(config)#interface gigabitEthernet 1/1
VSP-4850GTS:1(config-if)#no shut
VSP-4850GTS:1(config-if)#exit
VSP-4850GTS:1(config-if)#ip address 10.0.0.2 255.255.255.0
VSP-4850GTS:1(config-if)#ping 10.0.0.1
10.0.0.1 is alive
VSP-4850GTS:1(config-if)#
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.0.0
General Availability Released Software, Fully supported
AVAYA COMMAND LINE INTERFACE
Login: rwa
Password: ***
VSP-4850GTS:1>CP1 [01/01/70 00:36:59.029] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port
VSP-4850GTS:1>en
VSP-4850GTS:1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
VSP-4850GTS:1(config)#interface gigabitEthernet 1/1
VSP-4850GTS:1(config-if)#no shut
VSP-4850GTS:1(config-if)#exit
VSP-4850GTS:1(config-if)#ip address 10.0.0.2 255.255.255.0
VSP-4850GTS:1(config-if)#ping 10.0.0.1
10.0.0.1 is alive
VSP-4850GTS:1(config-if)#
Step 2:
- enable the FTP server on the VSP4850GTS
VSP-4850GTS:1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
VSP-4850GTS:1(config)#boot config flags ftpd
Enter configuration commands, one per line. End with CNTL/Z.
VSP-4850GTS:1(config)#boot config flags ftpd
Step 3:
- using WinSCP copy the .tgz file to the /intflash directory on the VSP4850GTS. In our example we are upgrading from 3.0.0.0 to 3.0.1.0 so the filename is "VSP4K.3.0.1.0.tgz"
Step 4:
- Add and activate the new sofware downloaded
VSP-4850GTS:1#software add VSP4K.3.0.1.0.tgz
Extracting distribution information from /intflash/VSP4K.3.0.1.0.tgz
Extracting software version 3.0.1.0.GA from /intflash/VSP4K.3.0.1.0.tgz
Extraction of 3.0.1.0.GA to /intflash/release/3.0.1.0.GA successful
Setting permissions on /intflash/release/3.0.1.0.GA successful
VSP-4850GTS:1#
VSP-4850GTS:1#software activate 3.0.1.0.GA
Executing software activate for version 3.0.1.0.GA.
Validating release 3.0.1.0.GA
Sending upgrade message to slots: 1. Version=3.0.1.0.GA
Slot 1 : IMAGE SYNC: Running pre-install script for image version 3.0.1.0.GA
Slot 1 : IMAGE SYNC: Uboot image is consistent
Slot 1 : IMAGE SYNC: Root FS image is being updated...
Slot 1 : IMAGE SYNC: App FS image is being updated...
Slot 1 : IMAGE SYNC: Running post-install script for image version 3.0.1.0.GA
Slot 1 : IMAGE SYNC: Backup image successfully upgraded to 3.0.1.0.GA
Primary Version: 3.0.1.0.GA
Backup Version: 3.0.0.0.GA
Changes will take effect on next reboot.
VSP-4850GTS:1#
Extracting distribution information from /intflash/VSP4K.3.0.1.0.tgz
Extracting software version 3.0.1.0.GA from /intflash/VSP4K.3.0.1.0.tgz
Extraction of 3.0.1.0.GA to /intflash/release/3.0.1.0.GA successful
Setting permissions on /intflash/release/3.0.1.0.GA successful
VSP-4850GTS:1#
VSP-4850GTS:1#software activate 3.0.1.0.GA
Executing software activate for version 3.0.1.0.GA.
Validating release 3.0.1.0.GA
Sending upgrade message to slots: 1. Version=3.0.1.0.GA
Slot 1 : IMAGE SYNC: Running pre-install script for image version 3.0.1.0.GA
Slot 1 : IMAGE SYNC: Uboot image is consistent
Slot 1 : IMAGE SYNC: Root FS image is being updated...
Slot 1 : IMAGE SYNC: App FS image is being updated...
Slot 1 : IMAGE SYNC: Running post-install script for image version 3.0.1.0.GA
Slot 1 : IMAGE SYNC: Backup image successfully upgraded to 3.0.1.0.GA
Primary Version: 3.0.1.0.GA
Backup Version: 3.0.0.0.GA
Changes will take effect on next reboot.
VSP-4850GTS:1#
Step 5:
- reboot without save if you wish to have a device with no config changes. If you would like to keep the FTP and IP address configured perform a "save config".
VSP-4850GTS:1#save config
CP-1: Save config to file /intflash/config.cfg successful.
VSP-4850GTS:1#CP1 [01/01/70 01:00:45.973] 0x000045e3 00000000 GlobalRouter SNMP INFO Save config successful.
VSP-4850GTS:1#reset
Are you sure you want to reset the switch (y/n) ? y
Setting release 3.0.1.0.GA
CP1 [01/01/70 01:00:53.881] 0x0027458a 00000000 GlobalRouter SW INFO Chassis reset initiated from CLI
CP1 [01/01/70 01:00:53.881] 0x0027458d 00000000 GlobalRouter SW INFO Resetting Chassis
CP1 [01/01/70 01:00:56.000] LifeCycle: INFO: Stopping all processes
CP1 [01/01/70 01:00:57.000] LifeCycle: INFO: All processes have stopped
CP1 [01/01/70 01:00:57.000] LifeCycle: INFO: Flushing buffers ... OK
CP1 [01/01/70 01:00:58.000] LifeCycle: WARNING: Restarting module
INIT: Sending processes the TERM signal
Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 1977)
.
Stopping vsp...
Deconfiguring network interfaces... done.
Stopping syslogd/klogd: stopped syslogd (pid 1982)
stopped klogd (pid 1984)
done
Sending all processes the TERM signal...
Sending all processes the KILL signal...
hwclock: can't open '/dev/misc/rtc': No such file or directory
Unmounting remote filesystems...
Stopping portmap daemon: portmap.
Deactivating swap...
Unmounting local filesystems...
Rebooting... [ 3388.326120] Restarting system.
U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C: ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S
DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI: Bus Dev VenId DevId Class Int
00:0f.0 - 14e4:b634 - Network controller
In: serial
Out: serial
Err: serial
Net: No ethernet found.
USB: Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-2.6.32.21-avaya-vsp4800
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1687686 Bytes = 1.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
Image Name: vsp-image-vsp4800-20130218193035
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10549358 Bytes = 10.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
Booting using the fdt blob at 0x0119c0c8
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [ 7.873348] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.069709] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.249227] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
e2fsck 1.41.14 (22-Dec-2010)
VSP Linux
Thu Jan 1 01:06:59 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...
CP1 [01/01/70 01:07:47] rc.appfs.vsp4k: Start
CP1 [01/01/70 01:07:47] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 01:07:47] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 01:07:47] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 01:07:49] ins-klm: Detected card type: cp
CP1 [01/01/70 01:07:49] ins-klm: Inserting wdd KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting TIPC
CP1 [01/01/70 01:07:49] ins-klm: Inserting tipc KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 01:07:49] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 01:07:49] ins-klm: Inserting evm KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting oxate KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting oxide KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting iodate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting k2 KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for K2
CP1 [01/01/70 01:07:50] ins-klm: Creating K2 device files
CP1 [01/01/70 01:07:50] ins-klm: Inserting BDE modules
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 01:07:51] Start: Starting Applications
CP1 [01/01/70 01:07:51] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 01:07:53.000] LifeCycle: INFO: Initial start
CP1 [01/01/70 01:07:53.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 01:07:54.000] Image Sync: Primary Release = 3.0.1.0.GA
CP1 [01/01/70 01:07:54.000] Image Sync: Backup Release = 3.0.0.0.GA
BANK1: 3.0.0.0.GA (G )
BANK2: 3.0.1.0.GA (C )
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
CP1 [01/01/70 01:07:55.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1 [01/01/70 01:08:01.236] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 01:08:02.831] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.
Virtual Services Platform 4800
System Software Release 3.0.1.0
Copyright (c) 2013 Avaya, Inc.
CP1 [01/01/70 01:08:02.832] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1 [01/01/70 01:08:03.533] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 01:08:03.533] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.1.0
CP1 [01/01/70 01:08:04.209] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 01:08:04.250] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 01:08:04.294] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 01:08:04.296] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 01:08:04.300] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 01:08:08.439] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 01:08:08.624] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1 [01/01/70 01:08:21.948] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 01:08:21.948] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 01:08:21.955] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg
SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole
CP1 [01/01/70 01:08:23.308] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 01:08:23.310] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 01:08:23.310] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file
Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.1.0
General Availability Released Software, Fully supported
AVAYA COMMAND LINE INTERFACE
Login: CP1 [01/01/70 01:08:25.839] 0x0000c5ec 00300001.239 DYNAMIC CLEAR GlobalRouter HW INFO Link Up(1/1)
CP-1: Save config to file /intflash/config.cfg successful.
VSP-4850GTS:1#CP1 [01/01/70 01:00:45.973] 0x000045e3 00000000 GlobalRouter SNMP INFO Save config successful.
VSP-4850GTS:1#reset
Are you sure you want to reset the switch (y/n) ? y
Setting release 3.0.1.0.GA
CP1 [01/01/70 01:00:53.881] 0x0027458a 00000000 GlobalRouter SW INFO Chassis reset initiated from CLI
CP1 [01/01/70 01:00:53.881] 0x0027458d 00000000 GlobalRouter SW INFO Resetting Chassis
CP1 [01/01/70 01:00:56.000] LifeCycle: INFO: Stopping all processes
CP1 [01/01/70 01:00:57.000] LifeCycle: INFO: All processes have stopped
CP1 [01/01/70 01:00:57.000] LifeCycle: INFO: Flushing buffers ... OK
CP1 [01/01/70 01:00:58.000] LifeCycle: WARNING: Restarting module
INIT: Sending processes the TERM signal
Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 1977)
.
Stopping vsp...
Deconfiguring network interfaces... done.
Stopping syslogd/klogd: stopped syslogd (pid 1982)
stopped klogd (pid 1984)
done
Sending all processes the TERM signal...
Sending all processes the KILL signal...
hwclock: can't open '/dev/misc/rtc': No such file or directory
Unmounting remote filesystems...
Stopping portmap daemon: portmap.
Deactivating swap...
Unmounting local filesystems...
Rebooting... [ 3388.326120] Restarting system.
U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C: ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S
DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI: Bus Dev VenId DevId Class Int
00:0f.0 - 14e4:b634 - Network controller
In: serial
Out: serial
Err: serial
Net: No ethernet found.
USB: Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-2.6.32.21-avaya-vsp4800
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1687686 Bytes = 1.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
Image Name: vsp-image-vsp4800-20130218193035
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10549358 Bytes = 10.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
Booting using the fdt blob at 0x0119c0c8
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [ 7.873348] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.069709] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.249227] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
e2fsck 1.41.14 (22-Dec-2010)
VSP Linux
Thu Jan 1 01:06:59 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...
CP1 [01/01/70 01:07:47] rc.appfs.vsp4k: Start
CP1 [01/01/70 01:07:47] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 01:07:47] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 01:07:47] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 01:07:49] ins-klm: Detected card type: cp
CP1 [01/01/70 01:07:49] ins-klm: Inserting wdd KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting TIPC
CP1 [01/01/70 01:07:49] ins-klm: Inserting tipc KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 01:07:49] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 01:07:49] ins-klm: Inserting evm KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting oxate KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting oxide KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting iodate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting k2 KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for K2
CP1 [01/01/70 01:07:50] ins-klm: Creating K2 device files
CP1 [01/01/70 01:07:50] ins-klm: Inserting BDE modules
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 01:07:51] Start: Starting Applications
CP1 [01/01/70 01:07:51] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 01:07:53.000] LifeCycle: INFO: Initial start
CP1 [01/01/70 01:07:53.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 01:07:54.000] Image Sync: Primary Release = 3.0.1.0.GA
CP1 [01/01/70 01:07:54.000] Image Sync: Backup Release = 3.0.0.0.GA
BANK1: 3.0.0.0.GA (G )
BANK2: 3.0.1.0.GA (C )
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036
CP1 [01/01/70 01:07:55.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1 [01/01/70 01:08:01.236] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 01:08:02.831] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.
Virtual Services Platform 4800
System Software Release 3.0.1.0
Copyright (c) 2013 Avaya, Inc.
CP1 [01/01/70 01:08:02.832] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1 [01/01/70 01:08:03.533] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 01:08:03.533] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.1.0
CP1 [01/01/70 01:08:04.209] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 01:08:04.250] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 01:08:04.294] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 01:08:04.296] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 01:08:04.300] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 01:08:08.439] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 01:08:08.624] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1 [01/01/70 01:08:21.948] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 01:08:21.948] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 01:08:21.955] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg
SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole
CP1 [01/01/70 01:08:23.308] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 01:08:23.310] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 01:08:23.310] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file
Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.1.0
General Availability Released Software, Fully supported
AVAYA COMMAND LINE INTERFACE
Login: CP1 [01/01/70 01:08:25.839] 0x0000c5ec 00300001.239 DYNAMIC CLEAR GlobalRouter HW INFO Link Up(1/1)
Step 6:
- commit software so that the upgrade is permanent. The VSP4850GTS out of the box has auto commit so if left running for 10 minutes the switch will commit the software itself, but if you power down the switch the software activate will not persist and upon powering the switch back up the old software will load.
Login: rwa
Password: ***
You are currently running a new version of code.
This release will be auto-committed in 9 minutes and 49 seconds.
Version Running: 3.0.1.0.GA
VSP-4850GTS:1>CP1 [01/01/70 01:08:34.375] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port
VSP-4850GTS:1>en
VSP-4850GTS:1#software commit
Executing software commit for version 3.0.1.0.GA.
VSP-4850GTS:1#show software
================================================================================
software releases in /intflash/release/
================================================================================
3.0.0.0.GA (Backup Release)
3.0.1.0.GA (Primary Release)
--------------------------------------------------------------------------------
Auto Commit : enabled
Commit Timeout : 10 minutes
VSP-4850GTS:1#
Password: ***
You are currently running a new version of code.
This release will be auto-committed in 9 minutes and 49 seconds.
Version Running: 3.0.1.0.GA
VSP-4850GTS:1>CP1 [01/01/70 01:08:34.375] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port
VSP-4850GTS:1>en
VSP-4850GTS:1#software commit
Executing software commit for version 3.0.1.0.GA.
VSP-4850GTS:1#show software
================================================================================
software releases in /intflash/release/
================================================================================
3.0.0.0.GA (Backup Release)
3.0.1.0.GA (Primary Release)
--------------------------------------------------------------------------------
Auto Commit : enabled
Commit Timeout : 10 minutes
VSP-4850GTS:1#
And that's it, not the most complex procedure, but not the easiest.
Please leave a comment if you have any questions or if you have found this guide to be useful. I will attempt to get back to you in a timely manner.
No comments:
Post a Comment