The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.
Device is running software version 3.1.0.2
Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)
U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX
Reset Status:
CPU: e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C: ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S
DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI: Bus Dev VenId DevId Class Int
00:0f.0 - 14e4:b634 - Network controller
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Verifying diag image checksum... OK.
Loading diagnostics image... DONE.
Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets: 9.
Dip Switch in Non-Base Unit position
RAM size: 1GB
FLASH size: 64MB
Super ISO is present
Attaching SOC unit 0... PCI device ASIC attached as unit 0
Diagnostics 5.6.2.51 Apr 2 2013, 13:24:15
Press Control-C to Enter Diag
Test 106 USB Register Test - PASSED
Test 111 DDRAM Walking 1/0s - PASSED
Test 112 DDRAM Byte/Word/Long - PASSED
Test 113 DDRAM Power-of-2 - PASSED
Test 121 ROM Config - PASSED
Test 151 FANs Status - PASSED
Test 207 XGS SWITCH Registers - PASSED
Test 221 PHYs Register - PASSED
Test 271 Ports Internal Loopback - PASSED
Starting Agent Version: 5.6.2.051
U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C: ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S
DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI: Bus Dev VenId DevId Class Int
00:0f.0 - 14e4:b634 - Network controller
In: serial
Out: serial
Err: serial
Net: No ethernet found.
USB: Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-2.6.32.21-avaya-vsp4800
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1687686 Bytes = 1.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
Image Name: vsp-image-vsp4800-20130218193035
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10549358 Bytes = 10.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
Booting using the fdt blob at 0x0119c0c8
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [ 7.870638] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.065540] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.242491] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda3: 131/83424 files (9.2% non-contiguous), 44350/333568 blocks
VSP Linux
Thu Jan 1 01:42:08 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...
Writing 4-byte value 797986d0 to e1000000 in /dev/mem
DISABLING CPLD WatchDog completed OK.
CP1 [01/01/70 01:42:59] rc.appfs.vsp4k: Start
CP1 [01/01/70 01:42:59] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 01:42:59] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 01:42:59] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 01:43:01] ins-klm: Detected card type: cp
CP1 [01/01/70 01:43:01] ins-klm: Inserting wdd KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting TIPC
CP1 [01/01/70 01:43:01] ins-klm: Inserting tipc KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 01:43:01] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 01:43:01] ins-klm: Inserting evm KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting oxate KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting oxide KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting iodate KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting k2 KLM
CP1 [01/01/70 01:43:02] ins-klm: Creating device nodes for K2
CP1 [01/01/70 01:43:02] ins-klm: Creating K2 device files
CP1 [01/01/70 01:43:02] ins-klm: Inserting BDE modules
CP1 [01/01/70 01:43:02] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 01:43:02] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 01:43:03] Start: Starting Applications
CP1 [01/01/70 01:43:03] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 01:43:04.000] LifeCycle: INFO: Read restart value of: 1
CP1 [01/01/70 01:43:05.000] LifeCycle: WARNING: Restart count:1
CP1 [01/01/70 01:43:05.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 01:43:06.000] Image Sync: Primary Release = 3.1.0.2.GA
CP1 [01/01/70 01:43:06.000] Image Sync: Backup Release = 3.1.0.0.GA
BANK1: 3.1.0.0.GA
BANK2: 3.1.0.2.GA (CG)
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
CP1 [01/01/70 01:43:07.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1 [01/01/70 01:43:13.385] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 01:43:15.207] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.
Virtual Services Platform 4800
System Software Release 3.1.0.2
Copyright (c) 2014 Avaya, Inc.
CP1 [01/01/70 01:43:15.208] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1 [01/01/70 01:43:16.118] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 01:43:16.118] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.1.0.2
CP1 [01/01/70 01:43:16.801] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 01:43:16.842] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 01:43:16.884] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 01:43:16.886] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 01:43:16.892] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 01:43:20.421] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 01:43:20.439] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1 [01/01/70 01:43:35.688] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 01:43:35.688] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 01:43:35.695] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg
SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole
CP1 [01/01/70 01:43:36.817] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 01:43:36.819] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 01:43:36.819] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file
Copyright(c) 2010-2014 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.1.0.2
General Availability Released Software, Fully supported
AVAYA COMMAND LINE INTERFACE
Login: CP1 [01/01/70 01:44:25.255] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1 [01/01/70 01:45:36.815] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful
Reset Status:
CPU: e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C: ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S
DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI: Bus Dev VenId DevId Class Int
00:0f.0 - 14e4:b634 - Network controller
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Verifying diag image checksum... OK.
Loading diagnostics image... DONE.
Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets: 9.
Dip Switch in Non-Base Unit position
RAM size: 1GB
FLASH size: 64MB
Super ISO is present
Attaching SOC unit 0... PCI device ASIC attached as unit 0
Diagnostics 5.6.2.51 Apr 2 2013, 13:24:15
Press Control-C to Enter Diag
Test 106 USB Register Test - PASSED
Test 111 DDRAM Walking 1/0s - PASSED
Test 112 DDRAM Byte/Word/Long - PASSED
Test 113 DDRAM Power-of-2 - PASSED
Test 121 ROM Config - PASSED
Test 151 FANs Status - PASSED
Test 207 XGS SWITCH Registers - PASSED
Test 221 PHYs Register - PASSED
Test 271 Ports Internal Loopback - PASSED
Starting Agent Version: 5.6.2.051
U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX
Reset Status: Software Hard, External/Internal Soft, External/Internal Hard
CPU: e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C: ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S
DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI: Bus Dev VenId DevId Class Int
00:0f.0 - 14e4:b634 - Network controller
In: serial
Out: serial
Err: serial
Net: No ethernet found.
USB: Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-2.6.32.21-avaya-vsp4800
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1687686 Bytes = 1.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
Image Name: vsp-image-vsp4800-20130218193035
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 10549358 Bytes = 10.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
Booting using the fdt blob at 0x0119c0c8
Uncompressing Kernel Image ... OK
Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit
INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [ 7.870638] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.065540] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.242491] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda3: 131/83424 files (9.2% non-contiguous), 44350/333568 blocks
VSP Linux
Thu Jan 1 01:42:08 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...
Writing 4-byte value 797986d0 to e1000000 in /dev/mem
DISABLING CPLD WatchDog completed OK.
CP1 [01/01/70 01:42:59] rc.appfs.vsp4k: Start
CP1 [01/01/70 01:42:59] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 01:42:59] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 01:42:59] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 01:43:01] ins-klm: Detected card type: cp
CP1 [01/01/70 01:43:01] ins-klm: Inserting wdd KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting TIPC
CP1 [01/01/70 01:43:01] ins-klm: Inserting tipc KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 01:43:01] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 01:43:01] ins-klm: Inserting evm KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting oxate KLM
CP1 [01/01/70 01:43:01] ins-klm: Inserting oxide KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting iodate KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting k2 KLM
CP1 [01/01/70 01:43:02] ins-klm: Creating device nodes for K2
CP1 [01/01/70 01:43:02] ins-klm: Creating K2 device files
CP1 [01/01/70 01:43:02] ins-klm: Inserting BDE modules
CP1 [01/01/70 01:43:02] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 01:43:02] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 01:43:02] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 01:43:03] Start: Starting Applications
CP1 [01/01/70 01:43:03] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 01:43:04.000] LifeCycle: INFO: Read restart value of: 1
CP1 [01/01/70 01:43:05.000] LifeCycle: WARNING: Restart count:1
CP1 [01/01/70 01:43:05.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 01:43:06.000] Image Sync: Primary Release = 3.1.0.2.GA
CP1 [01/01/70 01:43:06.000] Image Sync: Backup Release = 3.1.0.0.GA
BANK1: 3.1.0.0.GA
BANK2: 3.1.0.2.GA (CG)
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004
CP1 [01/01/70 01:43:07.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1 [01/01/70 01:43:13.385] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 01:43:15.207] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.
Virtual Services Platform 4800
System Software Release 3.1.0.2
Copyright (c) 2014 Avaya, Inc.
CP1 [01/01/70 01:43:15.208] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1 [01/01/70 01:43:16.118] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 01:43:16.118] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.1.0.2
CP1 [01/01/70 01:43:16.801] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 01:43:16.842] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 01:43:16.884] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 01:43:16.886] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 01:43:16.892] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 01:43:20.421] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 01:43:20.439] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1 [01/01/70 01:43:35.688] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 01:43:35.688] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 01:43:35.695] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg
SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.
SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole
CP1 [01/01/70 01:43:36.817] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 01:43:36.819] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 01:43:36.819] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file
Copyright(c) 2010-2014 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.1.0.2
General Availability Released Software, Fully supported
AVAYA COMMAND LINE INTERFACE
Login: CP1 [01/01/70 01:44:25.255] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1 [01/01/70 01:45:36.815] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful
No comments:
Post a Comment