Fission Division

Tuesday, 15 April 2014

Avaya VSP4850GTS boot sequence after power on (software version 3.1.0.0)

The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.1.0.0

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Verifying diag image checksum... OK.
Loading diagnostics image... DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         8.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr 2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106 USB   Register Test             - PASSED
Test 111 DDRAM Walking 1/0s              - PASSED
Test 112 DDRAM Byte/Word/Long            - PASSED
Test 113 DDRAM Power-of-2                - PASSED
Test 121 ROM   Config                    - PASSED
Test 151 FANs Status                    - PASSED
Test 207 XGS   SWITCH Registers          - PASSED
Test 221 PHYs Register                  - PASSED
Test 271 Ports Internal Loopback         - PASSED

Starting Agent Version: 5.6.2.051

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/a/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/a/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.866695] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.055474] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.232988] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.7% non-contiguous), 86877/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.7% non-contiguous), 86877/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Block bitmap differences: -229938
Fix? yes

Free blocks count wrong for group #7 (29171, counted=29172).
Fix? yes

Free blocks count wrong (270821, counted=270822).
Fix? yes

/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
/dev/sda3: 130/83424 files (7.7% non-contiguous), 62746/333568 blocks
VSP Linux
Thu Jan 1 01:25:58 UTC 1970
Uncompressing appfs 'A' ... done
Starting vsp application...
Writing 4-byte value 797984d0 to e1000000 in /dev/mem
DISABLING CPLD WatchDog completed OK.

CP1 [01/01/70 01:26:50] rc.appfs.vsp4k: Start
CP1 [01/01/70 01:26:51] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 01:26:51] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 01:26:50] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 01:26:52] ins-klm: Detected card type: cp
CP1 [01/01/70 01:26:52] ins-klm: Inserting wdd KLM
CP1 [01/01/70 01:26:52] ins-klm: Inserting TIPC
CP1 [01/01/70 01:26:52] ins-klm: Inserting tipc KLM
CP1 [01/01/70 01:26:52] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 01:26:52] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 01:26:52] ins-klm: Inserting evm KLM
CP1 [01/01/70 01:26:52] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 01:26:52] ins-klm: Inserting oxate KLM
CP1 [01/01/70 01:26:53] ins-klm: Inserting oxide KLM
CP1 [01/01/70 01:26:53] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 01:26:53] ins-klm: Inserting iodate KLM
CP1 [01/01/70 01:26:53] ins-klm: Inserting k2 KLM
CP1 [01/01/70 01:26:53] ins-klm: Creating device nodes for K2
CP1 [01/01/70 01:26:53] ins-klm: Creating K2 device files
CP1 [01/01/70 01:26:53] ins-klm: Inserting BDE modules
CP1 [01/01/70 01:26:53] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 01:26:53] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 01:26:53] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 01:26:54] Start: Starting Applications
CP1 [01/01/70 01:26:54] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 01:26:55.000] LifeCycle: INFO: Read restart value of: 1
CP1 [01/01/70 01:26:56.000] LifeCycle: WARNING: Restart count:1
CP1 [01/01/70 01:26:56.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 01:26:57.000] Image Sync: Primary Release = 3.1.0.0.GA
CP1 [01/01/70 01:26:57.000] Image Sync: Backup Release = 3.0.1.0.GA

BANK1: 3.1.0.0.GA (CG)
BANK2: 3.0.1.0.GA
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.1.0.0int050
Bank 2: Release Version = VSP4K.3.0.1.0int036

CP1 [01/01/70 01:26:58.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1 [01/01/70 01:27:04.451] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 01:27:06.196] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.

Virtual Services Platform 4800
System Software Release 3.1.0.0
Copyright (c) 2013 Avaya, Inc.

CP1 [01/01/70 01:27:06.197] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1 [01/01/70 01:27:07.049] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 01:27:07.049] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.1.0.0
CP1 [01/01/70 01:27:07.729] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 01:27:07.768] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 01:27:07.811] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 01:27:07.813] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 01:27:07.816] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 01:27:11.343] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 01:27:11.373] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1 [01/01/70 01:27:26.343] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 01:27:26.344] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 01:27:26.351] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg

SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1 [01/01/70 01:27:27.477] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 01:27:27.479] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 01:27:27.479] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.1.0.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1 [01/01/70 01:28:16.174] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1 [01/01/70 01:29:27.474] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful

Avaya VSP4850GTS boot sequence after power on (software version 3.0.1.0)

The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.0.1.0

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Verifying diag image checksum... OK.
Loading diagnostics image... DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         7.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr 2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106 USB   Register Test             - PASSED
Test 111 DDRAM Walking 1/0s              - PASSED
Test 112 DDRAM Byte/Word/Long            - PASSED
Test 113 DDRAM Power-of-2                - PASSED
Test 121 ROM   Config                    - PASSED
Test 151 FANs Status                    - PASSED
Test 207 XGS   SWITCH Registers          - PASSED
Test 221 PHYs Register                  - PASSED
Test 271 Ports Internal Loopback         - PASSED

Starting Agent Version: 5.6.2.051

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.857761] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.047291] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.224094] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.5% non-contiguous), 86075/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.5% non-contiguous), 86075/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda3: 125/83424 files (5.6% non-contiguous), 62306/333568 blocks
VSP Linux
Thu Jan 1 01:06:59 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...

CP1 [01/01/70 01:07:47] rc.appfs.vsp4k: Start
CP1 [01/01/70 01:07:48] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 01:07:48] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 01:07:48] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 01:07:50] ins-klm: Detected card type: cp
CP1 [01/01/70 01:07:50] ins-klm: Inserting wdd KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting TIPC
CP1 [01/01/70 01:07:50] ins-klm: Inserting tipc KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 01:07:50] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 01:07:50] ins-klm: Inserting evm KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting oxate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting oxide KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting iodate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting k2 KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for K2
CP1 [01/01/70 01:07:50] ins-klm: Creating K2 device files
CP1 [01/01/70 01:07:50] ins-klm: Inserting BDE modules
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 01:07:51] Start: Starting Applications
CP1 [01/01/70 01:07:52] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 01:07:53.000] LifeCycle: INFO: Read restart value of: 0
CP1 [01/01/70 01:07:54.000] LifeCycle: INFO: Initial start
CP1 [01/01/70 01:07:54.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 01:07:55.000] Image Sync: Primary Release = 3.0.1.0.GA
CP1 [01/01/70 01:07:55.000] Image Sync: Backup Release = 3.0.0.0.GA

BANK1: 3.0.0.0.GA
BANK2: 3.0.1.0.GA (CG)
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

CP1 [01/01/70 01:07:56.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1 [01/01/70 01:08:02.000] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 01:08:03.376] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.

Virtual Services Platform 4800
System Software Release 3.0.1.0
Copyright (c) 2013 Avaya, Inc.

CP1 [01/01/70 01:08:03.377] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1 [01/01/70 01:08:04.297] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 01:08:04.297] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.1.0
CP1 [01/01/70 01:08:04.987] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 01:08:05.029] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 01:08:05.071] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 01:08:05.073] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 01:08:05.077] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 01:08:09.397] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 01:08:09.522] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1 [01/01/70 01:08:25.685] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 01:08:25.686] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 01:08:25.692] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg

SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1 [01/01/70 01:08:27.405] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 01:08:27.477] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 01:08:27.494] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.1.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1 [01/01/70 01:09:14.038] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1 [01/01/70 01:10:27.403] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful

How to upgrade a new "out of box" Avaya VSP4850GTS

This guide is to assist those that need an easy and quick guide to upgrade a brand new VSP4850GTS that has just been unboxed.

It is assumed that you know how to unbox the switch, insert power supply, apply power and console into the switch.

We are going to use VLAN1 (10.0.0.1) so we do not have to add a VLAN, use port 1 for the link to a workstation (10.0.0.2). The workstation used in this guide is a Windows 8 laptop and we are running WinSCP as the FTP client.

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

The encryption module will NOT be downloaded in this example.

Step 1:

Login to the switch and perform basic configuration to get the management up.
The default username is "rwa" and the default password is "rwa"

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.0.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: rwa
Password: ***

VSP-4850GTS:1>CP1 [01/01/70 00:36:59.029] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port

VSP-4850GTS:1>en
VSP-4850GTS:1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
VSP-4850GTS:1(config)#interface gigabitEthernet 1/1
VSP-4850GTS:1(config-if)#no shut
VSP-4850GTS:1(config-if)#exit
VSP-4850GTS:1(config-if)#ip address 10.0.0.2 255.255.255.0
VSP-4850GTS:1(config-if)#ping 10.0.0.1
10.0.0.1 is alive
VSP-4850GTS:1(config-if)#

Step 2:

enable the FTP server on the VSP4850GTS

VSP-4850GTS:1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
VSP-4850GTS:1(config)#boot config flags ftpd

Step 3:

using WinSCP copy the .tgz file to the /intflash directory on the VSP4850GTS. In our example we are upgrading from 3.0.0.0 to 3.0.1.0 so the filename is "VSP4K.3.0.1.0.tgz"

Step 4:

Add and activate the new sofware downloaded

VSP-4850GTS:1#software add VSP4K.3.0.1.0.tgz
Extracting distribution information from /intflash/VSP4K.3.0.1.0.tgz
Extracting software version 3.0.1.0.GA from /intflash/VSP4K.3.0.1.0.tgz
Extraction of 3.0.1.0.GA to /intflash/release/3.0.1.0.GA successful
Setting permissions on /intflash/release/3.0.1.0.GA successful
VSP-4850GTS:1#
VSP-4850GTS:1#software activate 3.0.1.0.GA
Executing software activate for version 3.0.1.0.GA.
Validating release 3.0.1.0.GA
Sending upgrade message to slots: 1. Version=3.0.1.0.GA

Slot 1 : IMAGE SYNC: Running pre-install script for image version 3.0.1.0.GA
Slot 1 : IMAGE SYNC: Uboot image is consistent
Slot 1 : IMAGE SYNC: Root FS image is being updated...
Slot 1 : IMAGE SYNC: App FS image is being updated...
Slot 1 : IMAGE SYNC: Running post-install script for image version 3.0.1.0.GA
Slot 1 : IMAGE SYNC: Backup image successfully upgraded to 3.0.1.0.GA

Primary Version: 3.0.1.0.GA
Backup Version: 3.0.0.0.GA

Changes will take effect on next reboot.
VSP-4850GTS:1#

Step 5:

reboot without save if you wish to have a device with no config changes. If you would like to keep the FTP and IP address configured perform a "save config".

VSP-4850GTS:1#save config
CP-1: Save config to file /intflash/config.cfg successful.

VSP-4850GTS:1#CP1 [01/01/70 01:00:45.973] 0x000045e3 00000000 GlobalRouter SNMP INFO Save config successful.

VSP-4850GTS:1#reset
Are you sure you want to reset the switch (y/n) ? y
Setting release 3.0.1.0.GA
CP1 [01/01/70 01:00:53.881] 0x0027458a 00000000 GlobalRouter SW INFO Chassis reset initiated from CLI
CP1 [01/01/70 01:00:53.881] 0x0027458d 00000000 GlobalRouter SW INFO Resetting Chassis
CP1 [01/01/70 01:00:56.000] LifeCycle: INFO: Stopping all processes
CP1 [01/01/70 01:00:57.000] LifeCycle: INFO: All processes have stopped
CP1 [01/01/70 01:00:57.000] LifeCycle: INFO: Flushing buffers ... OK
CP1 [01/01/70 01:00:58.000] LifeCycle: WARNING: Restarting module
INIT: Sending processes the TERM signal
Stopping OpenBSD Secure Shell server: sshdstopped /usr/sbin/sshd (pid 1977)
.
Stopping vsp...
Deconfiguring network interfaces... done.
Stopping syslogd/klogd: stopped syslogd (pid 1982)
stopped klogd (pid 1984)
done
Sending all processes the TERM signal...
Sending all processes the KILL signal...
hwclock: can't open '/dev/misc/rtc': No such file or directory
Unmounting remote filesystems...
Stopping portmap daemon: portmap.
Deactivating swap...
Unmounting local filesystems...
Rebooting... [ 3388.326120] Restarting system.

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.873348] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.069709] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.249227] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
e2fsck 1.41.14 (22-Dec-2010)
VSP Linux
Thu Jan 1 01:06:59 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...

CP1 [01/01/70 01:07:47] rc.appfs.vsp4k: Start
CP1 [01/01/70 01:07:47] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 01:07:47] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 01:07:47] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 01:07:49] ins-klm: Detected card type: cp
CP1 [01/01/70 01:07:49] ins-klm: Inserting wdd KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting TIPC
CP1 [01/01/70 01:07:49] ins-klm: Inserting tipc KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 01:07:49] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 01:07:49] ins-klm: Inserting evm KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting oxate KLM
CP1 [01/01/70 01:07:49] ins-klm: Inserting oxide KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting iodate KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting k2 KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for K2
CP1 [01/01/70 01:07:50] ins-klm: Creating K2 device files
CP1 [01/01/70 01:07:50] ins-klm: Inserting BDE modules
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 01:07:50] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 01:07:51] Start: Starting Applications
CP1 [01/01/70 01:07:51] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 01:07:53.000] LifeCycle: INFO: Initial start
CP1 [01/01/70 01:07:53.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 01:07:54.000] Image Sync: Primary Release = 3.0.1.0.GA
CP1 [01/01/70 01:07:54.000] Image Sync: Backup Release = 3.0.0.0.GA

BANK1: 3.0.0.0.GA (G )
BANK2: 3.0.1.0.GA (C )
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = VSP4K.3.0.1.0int036

CP1 [01/01/70 01:07:55.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1 [01/01/70 01:08:01.236] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 01:08:02.831] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.

Virtual Services Platform 4800
System Software Release 3.0.1.0
Copyright (c) 2013 Avaya, Inc.

CP1 [01/01/70 01:08:02.832] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1 [01/01/70 01:08:03.533] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 01:08:03.533] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.1.0
CP1 [01/01/70 01:08:04.209] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 01:08:04.250] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 01:08:04.294] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 01:08:04.296] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 01:08:04.300] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 01:08:08.439] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 01:08:08.624] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1 [01/01/70 01:08:21.948] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 01:08:21.948] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 01:08:21.955] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg

SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1 [01/01/70 01:08:23.308] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 01:08:23.310] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 01:08:23.310] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.1.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1 [01/01/70 01:08:25.839] 0x0000c5ec 00300001.239 DYNAMIC CLEAR GlobalRouter HW INFO Link Up(1/1)

Step 6:

commit software so that the upgrade is permanent. The VSP4850GTS out of the box has auto commit so if left running for 10 minutes the switch will commit the software itself, but if you power down the switch the software activate will not persist and upon powering the switch back up the old software will load.

Login: rwa
Password: ***

You are currently running a new version of code.

This release will be auto-committed in 9 minutes and 49 seconds.

Version Running: 3.0.1.0.GA

VSP-4850GTS:1>CP1 [01/01/70 01:08:34.375] 0x000305ca 00000000 GlobalRouter SW INFO user rwa connected via console port
VSP-4850GTS:1>en
VSP-4850GTS:1#software commit
Executing software commit for version 3.0.1.0.GA.

VSP-4850GTS:1#show software

================================================================================
software releases in /intflash/release/
================================================================================
3.0.0.0.GA (Backup Release)
3.0.1.0.GA (Primary Release)

--------------------------------------------------------------------------------
Auto Commit : enabled
Commit Timeout : 10 minutes

VSP-4850GTS:1#

And that's it, not the most complex procedure, but not the easiest.

Please leave a comment if you have any questions or if you have found this guide to be useful. I will attempt to get back to you in a timely manner.

Avaya VSP4850GTS boot sequence after power on (software version 3.0.0.0)

The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.0.0.0

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Verifying diag image checksum... OK.
Loading diagnostics image... DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         5.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr 2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106 USB   Register Test             - PASSED
Test 111 DDRAM Walking 1/0s              - PASSED
Test 112 DDRAM Byte/Word/Long            - PASSED
Test 113 DDRAM Power-of-2                - PASSED
Test 121 ROM   Config                    - PASSED
Test 151 FANs Status                    - PASSED
Test 207 XGS   SWITCH Registers          - PASSED
Test 221 PHYs Register                  - PASSED
Test 271 Ports Internal Loopback         - PASSED

Starting Agent Version: 5.6.2.051

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM: Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/a/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/a/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.870429] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.057096] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.235719] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.3% non-contiguous), 86012/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.3% non-contiguous), 86012/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Entry 'qos_profile' in /intflash (53089) has deleted/unused inode 53119. Clear? yes

Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information

/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
/dev/sda3: 79/83424 files (2.5% non-contiguous), 24822/333568 blocks
VSP Linux
Thu Jan 1 00:05:07 UTC 1970
Uncompressing appfs 'A' ... done
Starting vsp application...

CP1 [01/01/70 00:05:53] rc.appfs.vsp4k: Start
CP1 [01/01/70 00:05:53] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1 [01/01/70 00:05:53] rc.cgroups_class: Cgroup initialization complete.
CP1 [01/01/70 00:05:53] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1 [01/01/70 00:05:55] ins-klm: Detected card type: cp
CP1 [01/01/70 00:05:55] ins-klm: Inserting wdd KLM
CP1 [01/01/70 00:05:55] ins-klm: Inserting TIPC
CP1 [01/01/70 00:05:55] ins-klm: Inserting tipc KLM
CP1 [01/01/70 00:05:55] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1 [01/01/70 00:05:55] ins-klm: inserting KLMs from appfs
CP1 [01/01/70 00:05:55] ins-klm: Inserting evm KLM
CP1 [01/01/70 00:05:55] ins-klm: Inserting i2cs KLM
CP1 [01/01/70 00:05:55] ins-klm: Inserting oxate KLM
CP1 [01/01/70 00:05:55] ins-klm: Inserting oxide KLM
CP1 [01/01/70 00:05:55] ins-klm: Inserting carbonate KLM
CP1 [01/01/70 00:05:56] ins-klm: Inserting iodate KLM
CP1 [01/01/70 00:05:56] ins-klm: Inserting k2 KLM
CP1 [01/01/70 00:05:56] ins-klm: Creating device nodes for K2
CP1 [01/01/70 00:05:56] ins-klm: Creating K2 device files
CP1 [01/01/70 00:05:56] ins-klm: Inserting BDE modules
CP1 [01/01/70 00:05:56] ins-klm: Inserting linux-kernel-bde KLM
CP1 [01/01/70 00:05:56] ins-klm: Inserting linux-user-bde KLM
CP1 [01/01/70 00:05:56] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1 [01/01/70 00:05:57] Start: Starting Applications
CP1 [01/01/70 00:05:57] Start: Detected VSP4K Platform, disable patching
CP1 [01/01/70 00:05:58.000] LifeCycle: INFO: Read restart value of: 2
CP1 [01/01/70 00:05:59.000] LifeCycle: WARNING: Restart count:2
CP1 [01/01/70 00:05:59.000] LifeCycle: INFO: Starting all processes
CP1 [01/01/70 00:06:01.000] Image Sync: Primary Release = 3.0.0.0.GA
CP1 [01/01/70 00:06:01.000] Image Sync: Backup Release = 3.0.0.0.GA

BANK1: 3.0.0.0.GA (CG)
BANK2: Not Set
------------------------------------------------------------
Image Type: UBOOT
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = UNKNOWN

Image Type: KERNEL
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = UNKNOWN

Image Type: ROOT_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = UNKNOWN

Image Type: APP_FS
Bank 1: Release Version = VSP4K.3.0.0.0int064
Bank 2: Release Version = UNKNOWN

CP1 [01/01/70 00:06:01.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
WARNING: Check dummy: modes fastethernet_interface_configurationspanning-tree
WARNING: Check dummy: modes gigabitethernet_interface_configurationspanning-tree

Virtual Services Platform 4800
System Software Release 3.0.0.0
Copyright (c) 2013 Avaya, Inc.

CP1 [01/01/70 00:06:07.436] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1 [01/01/70 00:06:07.847] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1 [01/01/70 00:06:07.848] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.0.0
CP1 [01/01/70 00:06:08.548] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1 [01/01/70 00:06:08.584] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1 [01/01/70 00:06:08.626] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1 [01/01/70 00:06:08.628] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1 [01/01/70 00:06:08.632] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1 [01/01/70 00:06:09.483] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.
CP1 [01/01/70 00:06:09.486] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
Warning: Please save your configuration after boot-up to avoid SNMP access issues.
         RWA, L1, L2, L3 are all mapped to read/write community.
CP1 [01/01/70 00:06:13.176] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1 [01/01/70 00:06:13.251] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key

SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1 [01/01/70 00:06:29.540] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1 [01/01/70 00:06:29.541] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1 [01/01/70 00:06:29.556] 0x0008851c 00000000 GlobalRouter SW INFO Using factory default system configuration
CP1 [01/01/70 00:06:29.558] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1 [01/01/70 00:06:29.559] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1 [01/01/70 00:06:29.560] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.0.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

CP1 [01/01/70 00:06:30.561] 0x0003c736 00000000 GlobalRouter IP INFO the OSPF Md5 key file does not exist
Login: CP1 [01/01/70 00:07:17.804] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1 [01/01/70 00:08:29.557] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful

Wednesday, 28 August 2013

IPFire Core Update 72 released 28AUG13

An update for IPFire has been released, the following changes have been made

obtained from http://www.ipfire.org/news/ipfire-2-13-core-update-72-released

Today, IPFire 2.13 Core Update 72 and the crowd-funded Tor add-on have been released.
The Core Update comes with a lot of feature enhancements for IPsec, smaller fixes for OpenVPN and fixed two denial-of-service attacks in the Squid web proxy.

strongswan 5.1.0

strongswan, the software package that is responsible for IPsec VPN connections, has been updated to version 5.1.0. This is a major version, which fixes various kinds of bugs and also fixes a denial-of-service bug, which is of very little priority for IPFire users (CVE-2013-5013).

Elliptic Curve Cryptography

It is now possible to use Elliptic Curve Cryptography (ECC) groups in the Internet Key Exchange (IKE) protocols in addition to the previously defined Diffie-Hellman groups. Advantages of using these include better efficiency because the underlying integer arithmetic is much faster than the binary field arithmetic MODP uses. Also ECC requires much smaller keys in order to achieve the same level of security than the Diffie-Hellman algorithm does. Therefore less entropy is consumed.

Smaller default keys

As it has often been pointed out, it is a problem to gather enough entropy on some computers. This makes it hard to do a proper key exchange, because you need to generate keys for that which are of a certain length of random data. The default settings for the key length have been very high since IPFire 2.13 and are now lowered, because of the reasons above. Instead of 8192 bits, the highest selected MODP group uses 4096 bits long keys.
More technical reasons are to be found in the comments of #10396.

squid Web Proxy server

The squid web proxy server has got two denial-of-service issues that are fixed in this Core Update. It was able to crash the cache manager when authenticating and it was possible to crash the entire proxy server with requests with over-long domain names (more information about this).

OpenVPN fixes

The OpenVPN GUI does now more precise validation of the subnet that is used as a transfer network for OpenVPN N2N connections. Incorrect data let the openvpnctrl binary crash when a new connection was started and no firewall rules were added.
It is now permitted to leave the “remote” field empty on a N2N server site, which makes creating connections with clients from dynamic IP addresses easier.
OpenVPN client connections with more than one space character in their names work again.

Misc Changes

snort has been enabled to decode packets from non-Ethernet devices again.
Dynamic DNS supports all-inkl.com now.
This update comes with all the requirements you need for Tor.

Tor – Protecting Online Anonymity

The Tor add-on is finally released together with Core Update 72, which you need to install first if you want to use Tor. Please make sure to reboot your IPFire system after the Tor add-on has been installed.
Documentation about this add-on can be found on our wiki: Tor documentation
We would like to thank all the people who contributed to this wish on the IPFire wishlist. If you want to, there are other things you can support, so those get implemented soon, too!

Please note a deprecation warning for Xen 3.x users!

Monday, 19 August 2013

Turn off fan on Avaya ERS 3510GT-PWR+ (fanless mode)

Now you may be reading this article because you are the "poor" soul who has an Avaya ERS3510GT-PWR+ switch humming away in close proximity to you in your normally silent workspace, or you may be the support guy/gal who has just received the call from said "poor" soul who is complaining about this noisy switch.................

You may have also searching the internet for "turn off fan Avaya ERS 3510GT-PWR+" and come back with almost nothing but the following statement from the support documentation

The ERS 3510GT-PWR+ can operate in one of two different power “modes”. Low Power

Budget mode provides a maximum PoE budget of up to 60W across 8 ports (fanless mode),

while High Power Budget mode provides a maximum of 170 Watts of power across 8 ports

(fan mode). This provides average concurrent power of 7.5W per port in Lower Power Budget

mode or 21.25W per port in High Power Budget mode.

So how do you turn the annoying little fan off?

Its easy (once you know how) with the following two CLI commands.

3510GT-PWR+#conf t
3510GT-PWR+(config)#poe power-mode low-power-budget

Alternately you can perform the change using EDM/COM via the left menu by first click on "Power Management", then PoE, and finally selecting "Power Mode" from the top tab.

Success!

The annoying little fan turns off instantly and you are left with a silent device so you can get back to your thoughts.

BUT WAIT!!!!

I now require more PoE power to run my new IP cameras and wireless access points. Thats ok, you can either use EDM/COM as shown above and click on highPowerBudget or you can use the following CLI command

3510GT-PWR+(config)#poe power-mode high-power-budget

Finally........Success!

Please leave a comment if you have any questions or if you have found this guide to be useful. I will attempt to get back to you in a timely manner.

Thursday, 8 August 2013

IPFire Core Update 71 released 06AUG13

An update for IPFire has been released, the following changes have been made

obtained from http://www.ipfire.org/news/ipfire-2-13-core-update-71-released

This is the official release announcement for IPFire 2.13 – Core Update 71. This update comes with some new features and minor bug fixes.

Wireless Client on RED

It is now possible to assign a wireless adapter as the RED interface. A GUI has been written where you can configure wireless access points, to which the IPFire system will connect when in reach.
You will be able to configure backup access points, to which IPFire will switch when the first one is down or out of reach. You can prioritize them, so that you can connect to the best one when ever that is possible. All common encryption technologies are supported.
This was funded on the IPFire wishlist a while ago, but was delayed because of lack of testers.

DNS forwarding GUI

A new GUI has been written on which you are able to define different name servers than the public name servers for your DNS zones. So, you can use your internal name server for internal name resolution instead of the public one on the Internet.

Performance improvement of squidclamav

Scanning all the HTTP traffic that is going through the proxy is very costly and makes browsing slow. In this update, we put the squidclamav process “in front of the proxy”. It now trusts the cache and won’t scan data that’s coming from the cache again which results in a huge performance increase. You now don’t even reckon that your traffic is scanned for viruses.

snort 2.9.5

The Intrusion Detection System (IDS) snort has been updated to version 2.9.5. Updating the official ruleset from sourcefire is now possible, again.
The VRT community rules package which was not available for a long time has been re-added to the list of rule sources again.

Smaller changes

The USB modeswitch database has been updated. This software will configure UMTS/LTE/3G USB adapters that they can be used as modems. Now, more of this hardware is supported.
Allow squid, the Web proxy service, to open more files and connections at once (more open file descriptors). This will result in a higher performance and better stability under high loads.
The whois tool for whois lookups has been replaced by GNU jwhois. It is much more flexible and does not have an outdated database like the old one.
squidclamav freezing when accessing sites that are also available over IPv6 has been fixed.
MTU negotiation on PPPoE: The default MTU for DSL lines has been 1492 which is not working on all DSL lines. If not configured correctly, your DSL connection won’t be able to transport big packets. We now allow to leave that field empty so IPFire will try to negotiate an appropriate MTU on itself.

Add-ons

VDR 2.0 has been pushed to the stable tree.

Tor from the IPFire wishlist

Thanks to all the people who donated for integrating Tor into IPFire. You can still support this wish or support the advanced firewall GUI.
The Tor add-on is already well advanced, because we worked day and night on it for a couple of days. We are confident that we will be able to ship it with Core Update 72. For that, we will need testers, so please stay tuned for that.