Avaya VSP4850GTS boot sequence after power on (software version 3.1.0.2)

The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.1.0.2

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
 Verifying diag image checksum... OK.
 Loading diagnostics image...  DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         9.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106  USB   Register Test             - PASSED
Test 111  DDRAM Walking 1/0s              - PASSED
Test 112  DDRAM Byte/Word/Long            - PASSED
Test 113  DDRAM Power-of-2                - PASSED
Test 121  ROM   Config                    - PASSED
Test 151  FANs  Status                    - PASSED
Test 207  XGS   SWITCH Registers          - PASSED
Test 221  PHYs  Register                  - PASSED
Test 271  Ports Internal Loopback         - PASSED

Starting  Agent  Version:  5.6.2.051


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
 Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.870638] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.065540] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.242491] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
 Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.8% non-contiguous), 87099/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda3: 131/83424 files (9.2% non-contiguous), 44350/333568 blocks
VSP Linux
Thu Jan  1 01:42:08 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...
Writing 4-byte value 797986d0 to e1000000 in /dev/mem
 DISABLING CPLD WatchDog completed OK.

CP1  [01/01/70 01:42:59] rc.appfs.vsp4k: Start
CP1  [01/01/70 01:42:59] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1  [01/01/70 01:42:59] rc.cgroups_class: Cgroup initialization complete.
CP1  [01/01/70 01:42:59] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1  [01/01/70 01:43:01] ins-klm: Detected card type: cp
CP1  [01/01/70 01:43:01] ins-klm: Inserting wdd KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting TIPC
CP1  [01/01/70 01:43:01] ins-klm: Inserting tipc KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1  [01/01/70 01:43:01] ins-klm: inserting KLMs from appfs
CP1  [01/01/70 01:43:01] ins-klm: Inserting evm KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting i2cs KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting oxate KLM
CP1  [01/01/70 01:43:01] ins-klm: Inserting oxide KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting carbonate KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting iodate KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting k2 KLM
CP1  [01/01/70 01:43:02] ins-klm: Creating device nodes for K2
CP1  [01/01/70 01:43:02] ins-klm: Creating K2 device files
CP1  [01/01/70 01:43:02] ins-klm: Inserting BDE modules
CP1  [01/01/70 01:43:02] ins-klm: Inserting linux-kernel-bde KLM
CP1  [01/01/70 01:43:02] ins-klm: Inserting linux-user-bde KLM
CP1  [01/01/70 01:43:02] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1  [01/01/70 01:43:03] Start:  Starting Applications
CP1  [01/01/70 01:43:03] Start: Detected VSP4K Platform, disable patching
CP1  [01/01/70 01:43:04.000] LifeCycle: INFO: Read restart value of: 1
CP1  [01/01/70 01:43:05.000] LifeCycle: WARNING: Restart count:1
CP1  [01/01/70 01:43:05.000] LifeCycle: INFO: Starting all processes
CP1  [01/01/70 01:43:06.000] Image Sync: Primary Release = 3.1.0.2.GA
CP1  [01/01/70 01:43:06.000] Image Sync: Backup Release  = 3.1.0.0.GA

BANK1: 3.1.0.0.GA
BANK2: 3.1.0.2.GA (CG)
------------------------------------------------------------
 Image Type: UBOOT
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004

 Image Type: KERNEL
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004

 Image Type: ROOT_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004

 Image Type: APP_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.vsp4k_3.1.0.2int004


CP1  [01/01/70 01:43:07.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1  [01/01/70 01:43:13.385] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1  [01/01/70 01:43:15.207] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.


Virtual Services Platform 4800
System Software Release 3.1.0.2
Copyright (c) 2014 Avaya, Inc.

CP1  [01/01/70 01:43:15.208] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1  [01/01/70 01:43:16.118] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1  [01/01/70 01:43:16.118] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.1.0.2
CP1  [01/01/70 01:43:16.801] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1  [01/01/70 01:43:16.842] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1  [01/01/70 01:43:16.884] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1  [01/01/70 01:43:16.886] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1  [01/01/70 01:43:16.892] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1  [01/01/70 01:43:20.421] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1  [01/01/70 01:43:20.439] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1  [01/01/70 01:43:35.688] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1  [01/01/70 01:43:35.688] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1  [01/01/70 01:43:35.695] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg


SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.


SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1  [01/01/70 01:43:36.817] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1  [01/01/70 01:43:36.819] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1  [01/01/70 01:43:36.819] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2014 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.1.0.2
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1  [01/01/70 01:44:25.255] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1  [01/01/70 01:45:36.815] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful

Avaya VSP4850GTS boot sequence after power on (software version 3.1.0.0)

The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.1.0.0

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
 Verifying diag image checksum... OK.
 Loading diagnostics image...  DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         8.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106  USB   Register Test             - PASSED
Test 111  DDRAM Walking 1/0s              - PASSED
Test 112  DDRAM Byte/Word/Long            - PASSED
Test 113  DDRAM Power-of-2                - PASSED
Test 121  ROM   Config                    - PASSED
Test 151  FANs  Status                    - PASSED
Test 207  XGS   SWITCH Registers          - PASSED
Test 221  PHYs  Register                  - PASSED
Test 271  Ports Internal Loopback         - PASSED

Starting  Agent  Version:  5.6.2.051


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/a/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/a/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
 Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.866695] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.055474] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.232988] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
 Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.7% non-contiguous), 86877/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1036/128000 files (0.7% non-contiguous), 86877/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
Block bitmap differences:  -229938
Fix? yes

Free blocks count wrong for group #7 (29171, counted=29172).
Fix? yes

Free blocks count wrong (270821, counted=270822).
Fix? yes


/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
/dev/sda3: 130/83424 files (7.7% non-contiguous), 62746/333568 blocks
VSP Linux
Thu Jan  1 01:25:58 UTC 1970
Uncompressing appfs 'A' ... done
Starting vsp application...
Writing 4-byte value 797984d0 to e1000000 in /dev/mem
 DISABLING CPLD WatchDog completed OK.

CP1  [01/01/70 01:26:50] rc.appfs.vsp4k: Start
CP1  [01/01/70 01:26:51] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1  [01/01/70 01:26:51] rc.cgroups_class: Cgroup initialization complete.
CP1  [01/01/70 01:26:50] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1  [01/01/70 01:26:52] ins-klm: Detected card type: cp
CP1  [01/01/70 01:26:52] ins-klm: Inserting wdd KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting TIPC
CP1  [01/01/70 01:26:52] ins-klm: Inserting tipc KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1  [01/01/70 01:26:52] ins-klm: inserting KLMs from appfs
CP1  [01/01/70 01:26:52] ins-klm: Inserting evm KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting i2cs KLM
CP1  [01/01/70 01:26:52] ins-klm: Inserting oxate KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting oxide KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting carbonate KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting iodate KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting k2 KLM
CP1  [01/01/70 01:26:53] ins-klm: Creating device nodes for K2
CP1  [01/01/70 01:26:53] ins-klm: Creating K2 device files
CP1  [01/01/70 01:26:53] ins-klm: Inserting BDE modules
CP1  [01/01/70 01:26:53] ins-klm: Inserting linux-kernel-bde KLM
CP1  [01/01/70 01:26:53] ins-klm: Inserting linux-user-bde KLM
CP1  [01/01/70 01:26:53] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1  [01/01/70 01:26:54] Start:  Starting Applications
CP1  [01/01/70 01:26:54] Start: Detected VSP4K Platform, disable patching
CP1  [01/01/70 01:26:55.000] LifeCycle: INFO: Read restart value of: 1
CP1  [01/01/70 01:26:56.000] LifeCycle: WARNING: Restart count:1
CP1  [01/01/70 01:26:56.000] LifeCycle: INFO: Starting all processes
CP1  [01/01/70 01:26:57.000] Image Sync: Primary Release = 3.1.0.0.GA
CP1  [01/01/70 01:26:57.000] Image Sync: Backup Release  = 3.0.1.0.GA

BANK1: 3.1.0.0.GA (CG)
BANK2: 3.0.1.0.GA
------------------------------------------------------------
 Image Type: UBOOT
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: KERNEL
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: ROOT_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: APP_FS
  Bank 1: Release Version = VSP4K.3.1.0.0int050
  Bank 2: Release Version = VSP4K.3.0.1.0int036


CP1  [01/01/70 01:26:58.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1  [01/01/70 01:27:04.451] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1  [01/01/70 01:27:06.196] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.


Virtual Services Platform 4800
System Software Release 3.1.0.0
Copyright (c) 2013 Avaya, Inc.

CP1  [01/01/70 01:27:06.197] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1  [01/01/70 01:27:07.049] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1  [01/01/70 01:27:07.049] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.1.0.0
CP1  [01/01/70 01:27:07.729] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1  [01/01/70 01:27:07.768] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1  [01/01/70 01:27:07.811] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1  [01/01/70 01:27:07.813] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1  [01/01/70 01:27:07.816] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1  [01/01/70 01:27:11.343] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1  [01/01/70 01:27:11.373] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1  [01/01/70 01:27:26.343] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1  [01/01/70 01:27:26.344] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1  [01/01/70 01:27:26.351] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg


SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.


SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1  [01/01/70 01:27:27.477] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1  [01/01/70 01:27:27.479] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1  [01/01/70 01:27:27.479] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.1.0.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1  [01/01/70 01:28:16.174] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1  [01/01/70 01:29:27.474] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful

Avaya VSP4850GTS boot sequence after power on (software version 3.0.1.0)

The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.0.1.0

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
 Verifying diag image checksum... OK.
 Loading diagnostics image...  DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         7.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106  USB   Register Test             - PASSED
Test 111  DDRAM Walking 1/0s              - PASSED
Test 112  DDRAM Byte/Word/Long            - PASSED
Test 113  DDRAM Power-of-2                - PASSED
Test 121  ROM   Config                    - PASSED
Test 151  FANs  Status                    - PASSED
Test 207  XGS   SWITCH Registers          - PASSED
Test 221  PHYs  Register                  - PASSED
Test 271  Ports Internal Loopback         - PASSED

Starting  Agent  Version:  5.6.2.051


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/b/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/b/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
 Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.857761] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.047291] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.224094] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
 Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.5% non-contiguous), 86075/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.5% non-contiguous), 86075/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda3: 125/83424 files (5.6% non-contiguous), 62306/333568 blocks
VSP Linux
Thu Jan  1 01:06:59 UTC 1970
Uncompressing appfs 'B' ... done
Starting vsp application...

CP1  [01/01/70 01:07:47] rc.appfs.vsp4k: Start
CP1  [01/01/70 01:07:48] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1  [01/01/70 01:07:48] rc.cgroups_class: Cgroup initialization complete.
CP1  [01/01/70 01:07:48] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1  [01/01/70 01:07:50] ins-klm: Detected card type: cp
CP1  [01/01/70 01:07:50] ins-klm: Inserting wdd KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting TIPC
CP1  [01/01/70 01:07:50] ins-klm: Inserting tipc KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1  [01/01/70 01:07:50] ins-klm: inserting KLMs from appfs
CP1  [01/01/70 01:07:50] ins-klm: Inserting evm KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting i2cs KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting oxate KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting oxide KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting carbonate KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting iodate KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting k2 KLM
CP1  [01/01/70 01:07:50] ins-klm: Creating device nodes for K2
CP1  [01/01/70 01:07:50] ins-klm: Creating K2 device files
CP1  [01/01/70 01:07:50] ins-klm: Inserting BDE modules
CP1  [01/01/70 01:07:50] ins-klm: Inserting linux-kernel-bde KLM
CP1  [01/01/70 01:07:50] ins-klm: Inserting linux-user-bde KLM
CP1  [01/01/70 01:07:50] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1  [01/01/70 01:07:51] Start:  Starting Applications
CP1  [01/01/70 01:07:52] Start: Detected VSP4K Platform, disable patching
CP1  [01/01/70 01:07:53.000] LifeCycle: INFO: Read restart value of: 0
CP1  [01/01/70 01:07:54.000] LifeCycle: INFO: Initial start
CP1  [01/01/70 01:07:54.000] LifeCycle: INFO: Starting all processes
CP1  [01/01/70 01:07:55.000] Image Sync: Primary Release = 3.0.1.0.GA
CP1  [01/01/70 01:07:55.000] Image Sync: Backup Release  = 3.0.0.0.GA

BANK1: 3.0.0.0.GA
BANK2: 3.0.1.0.GA (CG)
------------------------------------------------------------
 Image Type: UBOOT
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: KERNEL
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: ROOT_FS
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036

 Image Type: APP_FS
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = VSP4K.3.0.1.0int036


CP1  [01/01/70 01:07:56.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
CP1  [01/01/70 01:08:02.000] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1  [01/01/70 01:08:03.376] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.


Virtual Services Platform 4800
System Software Release 3.0.1.0
Copyright (c) 2013 Avaya, Inc.

CP1  [01/01/70 01:08:03.377] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
CP1  [01/01/70 01:08:04.297] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1  [01/01/70 01:08:04.297] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.1.0
CP1  [01/01/70 01:08:04.987] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1  [01/01/70 01:08:05.029] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1  [01/01/70 01:08:05.071] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1  [01/01/70 01:08:05.073] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1  [01/01/70 01:08:05.077] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1  [01/01/70 01:08:09.397] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1  [01/01/70 01:08:09.522] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key
CP1  [01/01/70 01:08:25.685] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1  [01/01/70 01:08:25.686] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1  [01/01/70 01:08:25.692] 0x00088512 00000000 GlobalRouter SW INFO Loading configuration from /intflash/config.cfg


SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.


SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1  [01/01/70 01:08:27.405] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1  [01/01/70 01:08:27.477] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1  [01/01/70 01:08:27.494] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.1.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

Login: CP1  [01/01/70 01:09:14.038] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1  [01/01/70 01:10:27.403] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful

Avaya VSP4850GTS boot sequence after power on (software version 3.0.0.0)

The following output has been captured off the serial console port of an Avaya VSP4850GTS during its boot sequence after power on.

Device is running software version 3.0.0.0

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status:

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
 Verifying diag image checksum... OK.
 Loading diagnostics image...  DONE.

Ethernet Routing Switch 4850GTS
Reading MAC Address...
MAC Address: XX-XX-XX-XX-XX-XX
Resets:         5.

Dip Switch in Non-Base Unit position
RAM   size:    1GB
FLASH size:   64MB
Super ISO is present

Attaching SOC unit 0... PCI device ASIC attached as unit 0

Diagnostics   5.6.2.51   Apr  2 2013, 13:24:15

Press Control-C to Enter Diag

Test 106  USB   Register Test             - PASSED
Test 111  DDRAM Walking 1/0s              - PASSED
Test 112  DDRAM Byte/Word/Long            - PASSED
Test 113  DDRAM Power-of-2                - PASSED
Test 121  ROM   Config                    - PASSED
Test 151  FANs  Status                    - PASSED
Test 207  XGS   SWITCH Registers          - PASSED
Test 221  PHYs  Register                  - PASSED
Test 271  Ports Internal Loopback         - PASSED

Starting  Agent  Version:  5.6.2.051


U-Boot 2012.04 (Mar 26 2013 - 17:44:29)MPC83XX

Reset Status: Software Hard, External/Internal Soft, External/Internal Hard

CPU:   e300c1, MPC8347_TBGA_A, Rev: 3.0 at 533.336 MHz, CSB: 266.668 MHz
Board: Avaya VSP 4850 Switch
I2C:   ready
DRAM:  Detected UDIMM UG12T6400M8SU-C8S

   DDR RAM: 1 GiB (DDR2, 64-bit, CL=3, ECC off)
Now running in RAM - U-Boot at: 3ff79000
Flash: 64.5 MiB
PCI:   Bus Dev VenId DevId Class Int
  00:0f.0     - 14e4:b634 - Network controller
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
USB:   Register 1210012 NbrPorts 2
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/boot/a/uImage-vsp4800.bin" from usb device 0:2 (usbda2)
1700040 bytes read
Loading file "/boot/a/vsp-image-vsp4800.cpio.gz.u-boot" from usb device 0:2 (usbda2)
10549422 bytes read
 Found DTB file
WARNING: adjusting available memory to 30000000
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Linux-2.6.32.21-avaya-vsp4800
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1687686 Bytes = 1.6 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01800000 ...
   Image Name:   vsp-image-vsp4800-20130218193035
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    10549358 Bytes = 10.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 0119c0c8
   Booting using the fdt blob at 0x0119c0c8
   Uncompressing Kernel Image ... OK
   Loading Ramdisk to 2f5f0000, end 2ffff86e ... OK
   Loading Device Tree to 007fa000, end 007fffff ... OK
setup_arch: bootmem
vsp4800_setup_arch()
arch: exit

INIT: version 2.86 booting
Please wait: booting...
Starting udev
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cache
Creating /etc/default/bios... [    7.870429] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.057096] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    8.235719] sd 0:0:0:0: [sda] Assuming drive cache: write through
Configuring update-modules.
Configuring openssh-sshd.
 Adding system startup for /etc/init.d/sshd.
Configuring base-files.
Configuration for powerpc.generic not found, trying powerpc
Configuring network interfaces... 4800: done.
Starting portmap daemon: portmap.
net.ipv4.conf.default.rp_filter = 1
INIT: Entering runlevel: 5
Starting OpenBSD Secure Shell server: sshd
done.
Starting syslogd/klogd: done
Starting vsp...
e2fsck 1.41.14 (22-Dec-2010)
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.3% non-contiguous), 86012/128000 blocks
e2fsck 1.41.14 (22-Dec-2010)
/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
*****************************
*****************************
*****************************
[1970-01-01 00:00] fsck: dev=/dev/sda2 fsn=/dev/sda2
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information
/dev/sda2: 1023/128000 files (0.3% non-contiguous), 86012/128000 blocks
[1970-01-01 00:00] fsck: dev=/dev/sda3 fsn=/dev/sda3
fsck from util-linux-ng 2.18
Pass 1: Checking inodes, blocks, and sizes
Pass 2: Checking directory structure
Entry 'qos_profile' in /intflash (53089) has deleted/unused inode 53119.  Clear? yes

Pass 3: Checking directory connectivity
Pass 4: Checking reference counts
Pass 5: Checking group summary information

/dev/sda3: ***** FILE SYSTEM WAS MODIFIED *****
/dev/sda3: 79/83424 files (2.5% non-contiguous), 24822/333568 blocks
VSP Linux
Thu Jan  1 00:05:07 UTC 1970
Uncompressing appfs 'A' ... done
Starting vsp application...

CP1  [01/01/70 00:05:53] rc.appfs.vsp4k: Start
CP1  [01/01/70 00:05:53] rc.cgroups_class: Cgroup filesystem (dev/cpuctl) mounted for CFS
CP1  [01/01/70 00:05:53] rc.cgroups_class: Cgroup initialization complete.
CP1  [01/01/70 00:05:53] rc.appfs.vsp4k: Checking if tap_enet deamon is running ... [NO]
CP1  [01/01/70 00:05:55] ins-klm: Detected card type: cp
CP1  [01/01/70 00:05:55] ins-klm: Inserting wdd KLM
CP1  [01/01/70 00:05:55] ins-klm: Inserting TIPC
CP1  [01/01/70 00:05:55] ins-klm: Inserting tipc KLM
CP1  [01/01/70 00:05:55] ins-klm: Inserting TUN
modprobe: module tun not found in modules.dep
CP1  [01/01/70 00:05:55] ins-klm: inserting KLMs from appfs
CP1  [01/01/70 00:05:55] ins-klm: Inserting evm KLM
CP1  [01/01/70 00:05:55] ins-klm: Inserting i2cs KLM
CP1  [01/01/70 00:05:55] ins-klm: Inserting oxate KLM
CP1  [01/01/70 00:05:55] ins-klm: Inserting oxide KLM
CP1  [01/01/70 00:05:55] ins-klm: Inserting carbonate KLM
CP1  [01/01/70 00:05:56] ins-klm: Inserting iodate KLM
CP1  [01/01/70 00:05:56] ins-klm: Inserting k2 KLM
CP1  [01/01/70 00:05:56] ins-klm: Creating device nodes for K2
CP1  [01/01/70 00:05:56] ins-klm: Creating K2 device files
CP1  [01/01/70 00:05:56] ins-klm: Inserting BDE modules
CP1  [01/01/70 00:05:56] ins-klm: Inserting linux-kernel-bde KLM
CP1  [01/01/70 00:05:56] ins-klm: Inserting linux-user-bde KLM
CP1  [01/01/70 00:05:56] ins-klm: Creating device nodes for bde KLM {dev-id:126}
CP1  [01/01/70 00:05:57] Start:  Starting Applications
CP1  [01/01/70 00:05:57] Start: Detected VSP4K Platform, disable patching
CP1  [01/01/70 00:05:58.000] LifeCycle: INFO: Read restart value of: 2
CP1  [01/01/70 00:05:59.000] LifeCycle: WARNING: Restart count:2
CP1  [01/01/70 00:05:59.000] LifeCycle: INFO: Starting all processes
CP1  [01/01/70 00:06:01.000] Image Sync: Primary Release = 3.0.0.0.GA
CP1  [01/01/70 00:06:01.000] Image Sync: Backup Release  = 3.0.0.0.GA

BANK1: 3.0.0.0.GA (CG)
BANK2: Not Set
------------------------------------------------------------
 Image Type: UBOOT
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = UNKNOWN

 Image Type: KERNEL
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = UNKNOWN

 Image Type: ROOT_FS
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = UNKNOWN

 Image Type: APP_FS
  Bank 1: Release Version = VSP4K.3.0.0.0int064
  Bank 2: Release Version = UNKNOWN


CP1  [01/01/70 00:06:01.000] LifeCycle: INFO: All processes started
Attaching network interface lo0... done.
WARNING:  Check dummy: modes fastethernet_interface_configurationspanning-tree
WARNING:  Check dummy: modes gigabitethernet_interface_configurationspanning-tree


Virtual Services Platform 4800
System Software Release 3.0.0.0
Copyright (c) 2013 Avaya, Inc.

CP1  [01/01/70 00:06:07.436] 0x000005c4 00000000 GlobalRouter SW INFO Load License failed. No Valid Advanced or Premier License found.
CP1  [01/01/70 00:06:07.847] 0x00034594 00000000 GlobalRouter SW INFO System boot
CP1  [01/01/70 00:06:07.848] 0x00034595 00000000 GlobalRouter SW INFO VSP-4800 System Software Release 3.0.0.0
CP1  [01/01/70 00:06:08.548] 0x0001081c 00400010.1 DYNAMIC SET GlobalRouter HW INFO Slot 1 is initializing.
CP1  [01/01/70 00:06:08.584] 0x00010774 00000000 GlobalRouter HW INFO Detected 4850GTS chassis
CP1  [01/01/70 00:06:08.626] 0x00010729 00000000 GlobalRouter HW INFO Detected 4850GTS Power Supply in slot PS 1. Adding 300 watts to available power
CP1  [01/01/70 00:06:08.628] 0x0001081d 00400010.1 DYNAMIC CLEAR GlobalRouter HW INFO Slot 1 is finished initialization.
CP1  [01/01/70 00:06:08.632] 0x00010830 00000000 GlobalRouter HW INFO Detected 4850GTS module (Serial#: XXXXXXXXXXXX) in slot 1
CP1  [01/01/70 00:06:09.483] 0x000005f8 00000000 GlobalRouter SW INFO Trial Period will expire in 59 days.
CP1  [01/01/70 00:06:09.486] 0x00000641 00000001 DYNAMIC SET GlobalRouter SW INFO Licence trial period will expire in 59 days
Warning: Please save your configuration after boot-up to avoid SNMP access issues.
         RWA, L1, L2, L3 are all mapped to read/write community.
CP1  [01/01/70 00:06:13.176] 0x0008850f 00000000 GlobalRouter SW INFO Waiting for all cards to be ready for configuration download
CP1  [01/01/70 00:06:13.251] 0x00040601 00000000 GlobalRouter WEB INFO HTTPS: Using the existing Server Cert/Key

SNMP-v3 VACM configuration is currently using default parameters.
These parameters should be changed for maximum security.

SNMP-v3 USM configuration is currently using default parameters.
These parameters should be changed for maximum security.


SNMP-v3 Having more than one entry in Group-access table for the same group-name with different security levels can cause a security hole

CP1  [01/01/70 00:06:29.540] 0x00010750 00000000 GlobalRouter HW INFO Module 4850GTS in slot 1 is ready for configuration download
CP1  [01/01/70 00:06:29.541] 0x00010758 00000000 GlobalRouter HW INFO Downloading configuration to all cards
CP1  [01/01/70 00:06:29.556] 0x0008851c 00000000 GlobalRouter SW INFO Using factory default system configuration
CP1  [01/01/70 00:06:29.558] 0x00010757 00000000 GlobalRouter HW INFO Initial configuration download to all cards completed
CP1  [01/01/70 00:06:29.559] 0x0003458b 00000000 GlobalRouter SW INFO The system is ready
CP1  [01/01/70 00:06:29.560] 0x00004595 00000000 GlobalRouter SNMP INFO Booted with file

Copyright(c) 2010-2013 Avaya, Inc.
All Rights Reserved.
Virtual Services Platform 4800
Software Release Build 3.0.0.0
General Availability Released Software, Fully supported

AVAYA COMMAND LINE INTERFACE

CP1  [01/01/70 00:06:30.561] 0x0003c736 00000000 GlobalRouter IP INFO the OSPF Md5 key file does not exist
Login: CP1  [01/01/70 00:07:17.804] 0x000045e5 00400005 DYNAMIC SET GlobalRouter SNMP INFO Sending Cold-Start Trap
CP1  [01/01/70 00:08:29.557] 0x00088524 00000000 GlobalRouter SW INFO Boot sequence successful

Cisco ASA5505 boot sequence after power on (software version 9.1(2))

The following output has been captured off the serial console port of an Cisco ASA5505 during its boot sequence after power on.

Device is running software version 9.1(2)

Serial settings are: 9600 baud, 8 data bits, no parity and 1 stop bit (9600/8-N-1)

CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45

Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
 00  01  00   1022   2080  Host Bridge
 00  01  02   1022   2082  Chipset En/Decrypt 11
 00  0C  00   1148   4320  Ethernet           11
 00  0D  00   177D   0003  Network En/Decrypt 10
 00  0F  00   1022   2090  ISA Bridge
 00  0F  02   1022   2092  IDE Controller
 00  0F  03   1022   2093  Audio              10
 00  0F  04   1022   2094  Serial Bus         9
 00  0F  05   1022   2095  Serial Bus         9

Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON

Cisco Systems ROMMON Version (1.0(12)13) #0: Thu Aug 28 15:55:27 PDT 2008

Platform ASA5505

Use BREAK or ESC to interrupt boot.
Use SPACE to begin boot immediately.

Launching BootLoader...
Default configuration file contains 1 entry.

Searching / for images to boot.

Loading /asa912-k8.bin... Booting...
Platform ASA5505

Loading...
IO memory blocks requested from bigphys 32bit: 9928
Àdosfsck 2.11, 12 Mar 2005, FAT32, LFN
Starting check/repair pass.
Starting verification pass.
/dev/hda1: 168 files, 43218/62844 clusters
dosfsck(/dev/hda1) returned 0
Processor memory 343932928, Reserved memory: 62914560

Total SSMs found: 0

Total NICs found: 10
88E6095 rev 2 Gigabit Ethernet @ index 09 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 08 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 07 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 06 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 05 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 04 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 03 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 02 MAC: MACA.DDRE.SS00
88E6095 rev 2 Ethernet @ index 01 MAC: MACA.DDRE.SS00
y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: MACA.DDRE.SS00
imb_upgrade_thread: IMB in slot 0 is version 1.8
imb_upgrade_thread: IMB in slot 0 is being upgraded to 1.10
Verify the activation-key, it might take a while...
Running Permanent Activation Key: 0xOMITOMIT 0xOMITOMIT 0xOMITOMIT 0xOMITOMIT 0xOMITOMIT
Licensed features for this platform:
Maximum Physical Interfaces       : 8              perpetual
VLANs                             : 3              DMZ Restricted
Dual ISPs                         : Disabled       perpetual
VLAN Trunk Ports                  : 0              perpetual
Inside Hosts                      : 10             perpetual
Failover                          : Disabled       perpetual
Encryption-DES                    : Enabled        perpetual
Encryption-3DES-AES               : Enabled        perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 10             perpetual
Total VPN Peers                   : 12             perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
Cluster                           : Disabled       perpetual

This platform has a Base license.

IMBFS: Updating the IMB to v1.10. Please wait...
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
                             Boot microcode        : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode     : CNLite-MC-SSLm-PLUS-2_05
                             IPSec microcode       : CNlite-MC-IPSECm-MAIN-2.08
IMBFS: The IMB software was changed to v1.10.

Cisco Adaptive Security Appliance Software Version 9.1(2)

  ****************************** Warning *******************************
  This product contains cryptographic features and is
  subject to United States and local country laws
  governing, import, export, transfer, and use.
  Delivery of Cisco cryptographic products does not
  imply third-party authority to import, export,
  distribute, or use encryption. Importers, exporters,
  distributors and users are responsible for compliance
  with U.S. and local country laws. By using this
  product you agree to comply with applicable laws and
  regulations. If you are unable to comply with U.S.
  and local laws, return the enclosed items immediately.

  A summary of U.S. laws governing Cisco cryptographic
  products may be found at:
  http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

  If you require further assistance please contact us by
  sending email to export@cisco.com.
  ******************************* Warning *******************************

This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit (http://www.openssl.org/)
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
Copyright (c) 1998-2011 The OpenSSL Project.
All rights reserved.

This product includes software developed at the University of
California, Irvine for use in the DAV Explorer project
(http://www.ics.uci.edu/~webdav/)
Copyright (c) 1999-2005 Regents of the University of California.
All rights reserved.

Busybox, version 1.16.1, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301  USA
Busybox comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

DOSFSTOOLS, version 2.11, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307
675 Mass Ave, Cambridge, MA 02139
DOSFSTOOLS comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

grub, version 0.94, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307
grub comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

libgcc, version 4.3, Copyright (C) 2007 Free Software Foundation, Inc.
libgcc comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

libstdc++, version 4.3, Copyright (C) 2007 Free Software Foundation, Inc.
libstdc++ comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

Linux kernel, version 2.6.29.6, Copyright (C) 1989, 1991 Free Software
Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301  USA
Linux kernel comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

module-init-tools, version 3.10, Copyright (C) 1989, 1991 Free Software
Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module-init-tools comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

numactl, version 2.0.3, Copyright (C) 2008 SGI.
Author: Andi Kleen, SUSE Labs
Version 2.0.0 by Cliff Wickman, Chritopher Lameter and Lee Schermerhorn
numactl comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

pciutils, version 3.1.4, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301  USA
pciutils comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

readline, version 5.2, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111 USA
readline comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

udev, version 146, Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301  USA
udev comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under the General
Public License v.2 (http://www.gnu.org/licenses/gpl-2.0.html)
See User Manual (''Licensing'') for details.

Cisco Adapative Security Appliance Software, version 9.1,
Copyright (c) 1996-2013 by Cisco Systems, Inc.
Certain components of Cisco ASA Software, Version 9.1 are licensed under the GNU
Lesser Public License (LGPL) Version 2.1.  The software code licensed under LGPL
Version 2.1 is free software that comes with ABSOLUTELY NO WARRANTY.  You can
redistribute and/or modify such LGPL code under the terms of LGPL Version 2.1
(http://www.gnu.org/licenses/lgpl-2.1.html).  See User Manual for licensing
details.

                Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

                Cisco Systems, Inc.
                170 West Tasman Drive
                San Jose, California 95134-1706

Reading from flash...
!.
Cryptochecksum (unchanged): OMITOMIT OMITOMIT OMITOMIT
OMITOMIT
 
INFO: Power-On Self-Test in process.
...........................................................
INFO: Power-On Self-Test complete.
Type help or '?' for a list of available commands.
ciscoasa>

Ubiquiti Networks EdgeMAX router lite boot sequence after power on (software version 1.2.0)

The following output has been captured off the serial console port of an Ubiquiti Networks EdgeMAX router lite during its boot sequence after power on.

Device is running software version 1.2.0

Serial settings are: 115200 baud, 8 data bits, no parity and 1 stop bit (115200/8-N-1)

Looking for valid bootloader image....
Jumping to start of image at address 0xbfc80000


U-Boot 1.1.1 (UBNT Build ID: 4493936-g009d77b) (Build time: Sep 20 2012 - 15:48:51)

BIST check passed.
UBNT_E100 r1:2, r2:13, serial #: SERIALNUMBER
Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate)
DRAM: 512 MB
Clearing DRAM....... done
Flash: 4 MB
Net: octeth0, octeth1, octeth2

USB: (port 0) scanning bus for devices... 1 USB Devices found
scanning bus for storage devices...
Device 0: Vendor: Prod.: USB Flash Memory Rev: PMAP
Type: Removable Hard Disk
Capacity: 3745.0 MB = 3.6 GB (7669824 x 512) 0
reading vmlinux.64
........................................

8081560 bytes read
argv[2]: coremask=0x3
argv[3]: root=/dev/sda2
argv[4]: rootdelay=15
argv[5]: rw
argv[6]: rootsqimg=squashfs.img
argv[7]: rootsqwdir=w
argv[8]: mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom)
ELF file is 64 bit
Allocating memory for ELF segment: addr: 0xffffffff81100000 (adjusted to: 0x1100000), size 0x7f2a90
Allocated memory for ELF segment: addr: 0xffffffff81100000, size 0x7f2a90
Processing PHDR 0
Loading 79a980 bytes at ffffffff81100000
Clearing 58110 bytes at ffffffff8189a980
## Loading Linux kernel with entry point: 0xffffffff81105cd0 ...
Bootloader: Done loading app on coremask: 0x3
Linux version 2.6.32.13-UBNT (ancheng@ubnt-builder2) (gcc version 4.3.3 (Cavium Networks Version: 2_0_0 build 99) ) #1 SMP Tue Jun 4 14:54:28 PDT 2013
CVMSEG size: 2 cache lines (256 bytes)
Cavium Networks SDK-2.0
CPU revision is: 000d0601 (Cavium Octeon+)
Checking for the multiply/shift bug... no.
Checking for the daddiu bug... no.
Determined physical RAM map:
memory: 0000000000034000 @ 000000000186c000 (usable after init)
memory: 0000000006800000 @ 0000000001900000 (usable)
memory: 0000000007c00000 @ 0000000008200000 (usable)
memory: 000000000fc00000 @ 0000000410000000 (usable)
Wasting 350112 bytes for tracking 6252 unused pages
Zone PFN ranges:
DMA32 0x0000186c -> 0x00100000
Normal 0x00100000 -> 0x0041fc00
Movable zone start PFN for each node
early_node_map[4] active PFN ranges
0: 0x0000186c -> 0x000018a0
0: 0x00001900 -> 0x00008100
0: 0x00008200 -> 0x0000fe00
0: 0x00410000 -> 0x0041fc00
Cavium Hotplug: Available coremask 0x0
PERCPU: Embedded 10 pages/cpu @a8000000020b8000 s10624 r8192 d22144 u65536
pcpu-alloc: s10624 r8192 d22144 u65536 alloc=16*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 63895
Kernel command line: bootoctlinux $loadaddr coremask=0x3 root=/dev/sda2 rootdelay=15 rw rootsqimg=squashfs.img rootsqwdir=w mtdparts=phys_mapped_flash:512k(boot0),512k(boot1),64k@3072k(eeprom) console=ttyS0,115200
PID hash table entries: 1024 (order: 1, 8192 bytes)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Primary instruction cache 32kB, virtually tagged, 4 way, 64 sets, linesize 128 bytes.
Primary data cache 16kB, 64-way, 2 sets, linesize 128 bytes.
Memory: 483444k/491728k available (3478k kernel code, 8064k reserved, 4118k data, 208k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:152
Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=5000000)
Security Framework initialized
Mount-cache hash table entries: 256
Checking for the daddi bug... no.
SMP: Booting CPU01 (CoreId 1)...
CPU revision is: 000d0601 (Cavium Octeon+)
Brought up 2 CPUs
NET: Registered protocol family 16
bio: create slab at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource OCTEON_CVMCOUNT
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 2, 16384 bytes)
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
/proc/octeon_perf: Octeon performace counter interface loaded
octeon_wdt: Initial granularity 5 Sec.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering unionfs 2.5.11 (for 2.6.32.55)
msgmni has been set to 944
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1180000000800 (irq = 58) is a OCTEON
console [ttyS0] enabled
loop: module loaded
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
OcteonUSB: Detected 1 ports
OcteonUSB OcteonUSB.0: Octeon Host Controller
OcteonUSB OcteonUSB.0: new USB bus registered, assigned bus number 1
OcteonUSB OcteonUSB.0: irq 80, io mem 0x00000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
OcteonUSB: Registered HCD for port 0 on irq 80
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
Probing USB hub...
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 15
L2 lock: TLB refill 256 bytes
L2 lock: General exception 128 bytes
L2 lock: low-level interrupt 128 bytes
L2 lock: interrupt 640 bytes
L2 lock: memcpy 1152 bytes
Bootbus flash: Setting flash for 4MB flash at 0x1f800000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
3 cmdlinepart partitions found on MTD device phys_mapped_flash
Creating 3 MTD partitions on "phys_mapped_flash":
0x000000000000-0x000000080000 : "boot0"
0x000000080000-0x000000100000 : "boot1"
0x000000300000-0x000000310000 : "eeprom"
Waiting 15sec before mounting root device...
hub 1-0:1.0: activate --> -22
usb 1-1: new high speed USB device using OcteonUSB and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
scsi 0:0:0:0: Direct-Access USB Flash Memory PMAP PQ: 0 ANSI: 0 CCS
sd 0:0:0:0: [sda] 7669824 512-byte logical blocks: (3.92 GB/3.65 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] Attached SCSI removable disk
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda2, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (unionfs filesystem) on device 0:12.
Freeing unused kernel memory: 208k freed
Algorithmics/MIPS FPU Emulator v1.5
INIT: version 2.88 booting
INIT: Entering runlevel: 2
Starting routing daemon: rib.
Starting EdgeOS router: migrate rl-system configure.

Welcome to EdgeOS ubnt ttyS0

By logging in, accessing, or using the Ubiquiti product, you
acknowledge that you have read and understood the Ubiquiti
License Agreement (available in the Web UI at, by default,
http://192.168.1.1) and agree to be bound by its terms.

ubnt login:

Ubiquiti Networks EdgeMAX router lite software version 1.2.0 released 9JUL12

An update for Ubiquiti Networks EdgeMAX router has been released, the following changes have been made

obtained from http://community.ubnt.com/t5/EdgeMAX-Updates-Blog/EdgeMax-software-release-v1-2-0/ba-p/510277

EdgeMax software release v1.2.0 for EdgeRouter Lite and EdgeRouter PoE is now available from our downloads page: http://www.ubnt.com/download#edgemax.

This release adds support for the newly-announced EdgeRouter PoE model, new features, and enhancements and bug fixes. Many of these are inspired and contributed by the community, so thanks everyone for your participation and contributions! 


[Release Notes v1.2.0]

Changes since v1.1.0

New features

• Add support for new EdgeRouter PoE features (our Web page has more information including documentation for the EdgeRouter PoE).
• [HW acceleration] Add hardware acceleration support for IPv6 forwarding. It is disabled by default and can be enabled using the "system ipv6-offload enable" setting.
• [PBR] Add support for per-connection load balancing using connection marking and probabilistic matching

Changes and bug fixes

• [HW acceleration] Improve offload algorithms for timeout-sensitive applications. This may resolve/alleviate the timeout-related issues of certain applications reported previously.
• [HW acceleration] Improve offload algorithms for some netfilter operations
• [PPPoE] Add pppd-related attributes to RADIUS dictionary to support RADIUS Interim Accounting Updates (RFC 2869). This was suggested and tested by community members (see this thread)!
• [PPPoE] Allow specifying MTU 1500 for PPPoE client (RFC 4638). Note that there are still issues on the PPP side, and therefore using MTU 1500 may not work in some environments.
• [PPPoE] Allow VLAN interfaces to be used for PPPoE server
• [PPPoE] Don't set mru option if MTU is 1500, which enables RFC 4638 support (MTU 1500 for PPPoE) in some environments according to forum reports
• [PPPoE] Add IPv6 settings for PPPoE client interfaces, which allows a PPPoE client interface to work with IPv6 address according to forum reports
• [PPP] Enable IPv6 support in pppd build
• [IPv6] Add free-form "radvd-options" setting for radvd configuration. This may be useful for users who need to use certain radvd options that are not yet in the CLI configuration (e.g., as discussed here and here), for example:
  

  set interfaces ethernet eth0 ipv6 router-advert radvd-options "RDNSS 2620:0:ccc::2 2620:0:ccd::2 { };"

• [NetFlow] Add 'ingress-capture' setting for configuring where flows are captured. This is also suggested by community members in this thread.
• [CLI] Remove unnecessary quotes from config "commands" output, for example, the output of the "show configuration commands" operation command (previously all words are quoted; now only the values are)
• [DNS forwarding] Add "options" configuration setting to allow any dnsmasq options to be set from the configuration, for example,
  

  set service dns forwarding options "server=/remote.local/10.0.0.10"

• [Webproxy] Add support for using free blacklist for URL filtering, which supports blocking based on URL categories defined in the blacklist
• [Interface] Fix validation for duplicate IP address on bridge, tunnel, loopback, and pseudo-ethernet interfaces
• [Interface] Disallow deleting physical interfaces from configuration. This prevents accidental deletion and is implemented after discussions with community members.
• [Bridging] Fix offload-related performance issue with certain bridged interfaces. This should provide more consistent performance for all bridged interfaces.
• [System] Fix CVE-2013-1427 for lighttpd
• [System] Fix "rename system image" command
• [PPTP] Fix attribution for PPTP client scripts/templates
• [Web UI] Add support to show kernel routes in the Routing tab
• [Web UI] Fix a corner case where UI may stop working after some time (e.g., days). Several community members have reported such behavior (for example this thread), and this fix may resolve the issue.
• [Web UI] Allow specifying range of one IP for DHCP server
• [Web UI] Allow specifying /31 addresses to interface
• [Web UI] Fix some cosmetic issues (labels, widths, etc.)
• [QoS] Fix commit error with active PPPoE interface
• [Firewall] Fix commit error when applying ruleset whose creation fails
• [Firewall] Fix handling of port names with dash
• [Firewall] Fix "show firewall modify" command
• [IPsec] Fix CVE-2013-2944 for strongSwan
• [DHCP] Fix subnet validation to allow non-existent subnets, permitting DHCP relay operation, for example
• [DHCP] Add validation to require balanced quotes in free-form parameters

Updated software components

• Add wide-dhcpv6-client package. Note that there is no configuration support for this in the CLI yet. However, several community members have reported successes with this package (for example see discussions here and here) which is why we are including it.
• Update krb5 to 1.8.3+dfsg-4squeeze7: Fix CVE-2002-2443
• Add the "mtr" application
• Update PHP to 5.3.22
• Update bind9 to 1:9.7.3.dfsg-1~squeeze10: Fix CVE-2013-2266
• Update curl 7.21.0-2.1+squeeze3: Fix CVE-2013-1944
• Update ddclient to 3.8.1-1. This brings ddclient more up-to-date with better support for more providers (for example as tested by the community in this thread).
• Update libxml2 2.7.8.dfsg-2+squeeze7: Fix CVE-2013-0338, CVE-2013-0339